Quote:
Originally Posted by willig5  Mike, I am a little confused as to why you had to be a smart ass with me? I just simply ask how you turn out with your build?
I am also confused as to what your goals are, you said you were trying to get to 700 rwhp but only made 699 rwhp. Your post on 03/10/2009 (shown below for ease) states your goal was 1000 rwhp & 1000 + rwtq give or take a few. Well 300 rwhp short is taking a few for sure.
Reading through you build it sounds like you pulled out all of the stops and didn’t hold back on anything. So now my question is if it not the KB system holding you down 300 rwhp from your goal, just what is it? cubic inches, compression ratio, cam? Maybe this new inlet I keep reading about will add that 300 rwhp, if so it must be sucking through a straw now.
I would have thought any shop worth their weight in dog shit could have gotten you closer to your goals then this, given the fact you spared no expense. I don’t care who you are 300rwhp is a long way from 1000rwhp.
You must have used a shop with a 5 million dollar facility, and a 5 dollar mechanic, where you get a 5 dollar job? Sounds like you should have gotten $3.69 back in change. Or did you know you would be short 300 rwhp of your goal before you started this build?
Below is your post from 03/10/2009
TPE Kenne Bell Blown 434 LSX and Hannibal Lector Cam**
________________________________________
Well im not as well known on this site compared to corvette forum and svt as i got an unwelcome back push from a mod a while back on here. So anyway with that said i just wanted to share my new build with you guys as well that dont belong on either of those other two forums.
Well as some of you may know I had some issues when i tore down my 346 so i decided to go to bigger cubes and figured oh what the hell we will just go to a 408 and lots of boost. After some long thinking and many hours on the phone with Jeff we have come to some solid conclusions and im proud to say that Jeff and TPE is going to be building me a great motor that is going to absolutly make a brutal street car. So we ditched the whole 408-416 ls3 idea and came to a conclusion of an lsx 434.
My goals are 1000rwhp 1000+rwtq on straight pump gas give or take a few we shall see what the dyno says at the end of the tuning process
The run down:
TPE 434LSx!!!!!!!!
Motor components:
LSx Bowtie Block
Callies 4340 Forged Crank w/2.1" rod journals
Callies "New Design" H-I beam 6.125" Forged rods
ARP2000 Rod bolts
ARP2000 Main Studs, w/ARP2000 side bolts
Clevite "Coated" main & rod bearings
Clevite "Coated" cam bearings
Wiseco Forged Pistons
Total Seal Rings (Stainless Top, Napier 2nd.1.5,1.5,3.0)
Double Roller tining set
Ported/Shimmed Melling 10296 oil pump
Machining and Parts Preperation:
Cylinders Bored/Torque Plate honed
Block decked and Squared (deck prepped to a surface RA of 38)
Cam Journals Line Bored
Mains Line Bored
Rotating assembly fully balanced
Crank Bladed and lightened
Chamfered Oil holes, and micropolished bearing surfaces
ALL parts and block hand deburred
Bronze bushed lifter bores
Completely assembled, blueprinted, photographed, documented, and serial numbered
Heads/Valvetrain:
Cometic .060 MLS gaskets
TFS 245 or New GM 6 bolts heads (70cc chambers)
2.1" Inconel stainless intake valve, 1.60" Incolel stainless exhaust
Dual "Extreme" springs good to .660" (150# seat, 410# open, Ti retainers)
Chromoly pushrods
Comp "Pro Magnum" roller rockers
Upgraded ARP2000 6 bolt head studs (one step below L19's
25x/25x .61x/.61x 113+3 (Hannibal Lector Cam )
That is the jist of it for now. Much more coming including complete pictures of the build as well as all install info all the way up to the final tune on the car. The car will be breathing through a set of full 2" headers into a complete 3" x pipe all the way out with 3" straight pipes out the back(no mufflers no cats). Some of you who have noticed my other posts may have seen im not the quiet type. I told Jeff i wanted the baddest sounding and most rediculous cam possible while still having a decent driveability field as well as not losing any power by going to big.
With this said I am a younger guy and i just want to make it clear that this build will be a timely fashioned build depending on my cash flow and will most likey be completed in the next several months depending on how well things go for me.
Any questions just ask guys I am extremly pleased with everything TPE has offered me and would just like to say thanks to Jeff times a billion cause i would never have gotten this far without him and his wealth of knowledge.
Other things that are done to my car:
Kenne Bell 2.8 fully ported inlet manifold
8 rib
heavy duty tensioner assembly
etc
Car is mini tubed and fully caged
345 bfg tires on the back
full wet nitrous system
etc etc etc etc it could go on all day lol... |
Listen man i hate to be the one to break the bad news, but my post was just a joke, dont believe everything you read on the interweb's
My car is not finished and wont be untill i get enough time off work to finish it, to be honest its not my number one priority in life like most of the guys on here and it will be finished when it is finished. I have a 72 chevelle with nitrous that i have been toying with all summer 9.6's so far in it, and my other project car 70 nova just got its new TT's on the 632 bbc in it, so easily said above im in no rush and like to do things right the first time.
Only reason i was being a smart ass to you, was cause i thought you were being like these other dummy's and being one to me, sorry for the confusion.