1dirtybird

iTrader: (7)

My shop ive got a half of it roped off for the project!

I was thinking $7.50 and hour US.... Haha.

Btw.... Got an extra Pro Charger set-up laying around.....Cheap lol 0

1dirtyZ

iTrader: (1)

finally some progress

i had to build a new lifting cradle cause the first one i made was,,,well,,,, kinda flimsy

this one is made from much thicker material. this is really important cause you can't install the engine alone or remove the tranny by itself cause of how the flywheel fits ( more on that later ) so you have to mate them both on the ground then lift them as one unit into the car. This will have castors installed to make it easier to move the combo around and will have a jack adapter welded somwhere near the center of weight of the combo :



almost finished product :



i finally finished the clutch fork thingy



and i took the engine off the stand to install the adapter and flywheel:







notice how the flywheel is larger than the adapter opening , which means you have to install the adapter then the flywheel , then slip the trans on to the adapter studs ( can't do that while they are in the car) .

and here you see the engine on the lifting cradle :




so tomorow i have to:
- torque down the flywheel bolts
- pop in the pilot bearing
- and bolt up the clutch and tranny.
- lift up the engine/trans into the car.
- install all the accessories on the engine
- hook up clutch lines and shifter cables.
- install the powersteering pump and measure how long the lines need to be .

Marky522

iTrader: (8)

I am sure you realize this but, you need to install the clutch fork pin after installing the clutch assembly, as this is a pull style clutch and not a push style. The way we do it is to tape it in place to the flywheel, slide the transmission onto the engine then pin it... Its a BLAST to do it in the car.

Mark...

Lookin great

1dirtyZ

iTrader: (1)

marky you are reading my mind

i was looking at it yesterday an saying to myself that this will be soooo much fun

thanks for the heads up !

any how ,,,, on to progress

i torqued down the flywheel , poped in the pilot bearing , then got the disk and pressure plate on there :





thats when i hit a small snag , the pressure plate uses some funky size torx bit bolts, which i didn't have at the moment , so i just hand tightened it by hand till i get some proper grade 8 allen bolts tommorrow .

so i decided to just see how it looks when done

.
.
.
.
"one small step for man , a huge setback for porsche purists " :





i think at that moment i felt a teardrop hit the ground in stutgart

anyhow i almost had an "oh crap!" moment; when installing the trans on to the engine it looked like the starter ring would not fit into the bellhousing , but after a few words of pursuation it went in man do they have some tight clearances; you can see in the next pic the clearance between the ring and bellhousing is about nothing of an inch ( sorry for the out of focus pic but i could not get a proper pic no matter what i did )



i also made some templates for the heat shields that will cover the alternator and A/C compressor, i'll try to finish them soon using some sheetmetal or aluminum .

sooo, tommorow i'll get the allen bolts and finish bolting up the clutch , mate the trans to the engine , weld a few tabs on the lift cradle as well as castors and a jacking point to finalize it , then hopefully lift it into place in the car

and if i have time i should also mount the powersteering pump and figure out where to mount the reservoir ( its a GTO style unit with a remote resv. ) after that i have to take it off to compensate for the added thickness of the plate on the head by either machining the pad that the pump mounts to on the head or machining a bit off the back of the powersteering pulley so when i push it back on it lines up properly with the rest of the accesorries .

wish me luck

Marky522

iTrader: (8)

The factory bolts are triple square bolts, your making great progress.

Mark

1dirtyZ

iTrader: (1)

thanks again marky ( you should hang here more often )
so if i use the square bits i have here somewhere it would work ??
either way i'm getting the allen bolts and swapping them out just for ease of replacing them later down the road

themachasy

iTrader: (5)

Check google for metalnerd tools, its where I got my triple squares for the audi/vw stuff. I don't know what size the triple squares are but they're a PITA without the right tool.

THErobertH

16 pages of thread, every one worth it!!!!
great ideas, awesome swap, you mind if i get a copy of your porsche/chevy badge???

LS1-450

iTrader: (33)

1dirtyz, did you have to clean & seal the gas tank or was it OK? I pulled mine to clean & seal...made me wonder about yours. BTW, my tank contained 8 gallons of the nastiest turpentine smelling "hand cleaner." The donor car had been sitting for years.

1dirtyZ

iTrader: (1)

themachasy, thanks for the heads up !

theroberth , go right ahead and thanks for the kind words. check your PM's

Ls1-450 , this might sound strange , but i don't know what they add ( or not put in in the first place) to the gas we have here cause it never seems to go bad . i have a scout that sits for anywhere from six months to a year sometimes and the gas never goes bad ( the thing has a caddy engine with 11:1 compression , so i would know if the 95 octane i put in went bad ).
either way , i will pop the fuel pump cover on the tank and give it a looksee just to be safe

Jimbo1367

1DirtyZ,
Great progress

1dirtyZ

iTrader: (1)

well got to work on it again last night , i got the new allen keys for the pressure plate and did the tape track to hold the fork in place ( thanks marky) as i mated the engine and trans together for the last time ( i hope ). i was not planning on doing much more other than a few odds and ends here and there ,,,, but

at 12:55AM monday the 20th of Sept. 2010 - one day ahead of schedule - the engine got a new home

pics of the whole process :

i rolled the engine into place under the car and started to lower the car on to it , when it got close enough i started to raise the tans end up into location to bolt up the trans mount , then proceeded into lifting the engine into place :







after bolting up the head plates / motor mounts i proceeded to cut the umbilical cord



and now i have a fully self suspended engine









so now i a acheived a major milestone in the project , and things should start rolling a bit faster from now on

funny thing is a i got a bit caried away with the instalation and never finished the lifting cradle , thats why you see me using the engine hoist and the rolly thing underneath the engine , but now i know how important the cradle thingy is.

so next up on the list :

- replace the bolts i used on the head plate with allen bolts ( looks cleaner / better
- swap the gto oil pan to the kevko pan and pickup i have
- bolt up the suspension crossmember and finish tightening the engine mounts
- install accessories like the alternator and waterpump and other stuff.
- finish fabbing up the heatshields on the ac compressor and alt.
- finish ( or atleast start working on ) the engine compartment mini harness
- route the heater hoses under the car

that should be enough to get the car down and off the lift so i can roll it back and start working on the interior and engine electrics and harness.

after that its on to :

- palce engine harness and mount PCM
- intake / throttle and injectors
- power steering and lines
- mount rear bumper and trunk lid
- finalize coolant tubes
- install new dash ( converting from auto to manual requires swapping the under dash assembly for the pedals )
- widndow and regulator
- check gas tank
- and it goes on and on and on

Thomo5150

Nice work, keep it up........

Irish350

iTrader: (14)

lol@ your 95 octane never going bad, over in this desert we can only get 91

cant wait for the next update

Marky522

iTrader: (8)

Looks really good. I am at about roughly the same stage in my Porsche-LS swap, but not nearly as earth shattering as yours... I think Ferdinand just rolled over in his grave.... If you have any questions about any of the factory wiring etc just let me know.

Oh, BTW I hope you like a nice HEAVY clutch pedal, the turbo clutch without assist will help develop your left leg


Mark

Tainted

iTrader: (9)

lookin nice!!!

1dirtyZ

iTrader: (1)

loool, marky have you ever tried the early ram single disk clutches for an Fbody
i looked like a freak back then cause my left leg was so much bigger than the right one

and i appreciate the offer and i have a feeling i will be needing it soon

irish , it gets worse : gas in dubai andi think kuwait is 98 octane


anyhow , got cracking on it again and finished quite a bit of the things on the list above:
got the head plate bolts swapped out to allen bolts , swapped the pan and pickup tube, atttched the oil cooler lines, bolted up the suspension crossmember and tightened the engine mounts , mounted the alternator and bracket, installed the starter and the starter cable , bolted the driveshaft and tightened the axleshafts ( on the tranny side), and installed the swaybar.

up next is installing the headers and exhaust , water pump , tightening the axleshafts ( spindle side ) , bumper brackets , tightening the aluminum bumper , slapping on the bumper cover , and building the AC and alt. heatshields and i should be able to roll the car of the lift

i'm almost done with the bottom of the car but there are a few things i'm waiting on to really call it done. things like the ac lines and fittings to the compressor ,heater hoses ( still waiting on them) , and the mini harness .

i did get a few pics but its late and i'm too tired to upload and post them, will do it tommorow

1dirtyZ

iTrader: (1)

sexy oil pan and lines



axleshafts and driveshaft and another angle of that sexy oil pan ( don't you think i have an oil pan fixation )



forgot to mention that i installed the dipstick

FadedFD

iTrader: (5)

I don't know how this is going to work but that's a sick *** chassis to put that motor into! I can't wait to see this thing done.

bonecrrusher

iTrader: (1)

Holycrap - just realized this is staying 4wd.... is that Porsche transaxle going to hold the power from the LS motor?