3.5" aluminum driveshaft - 1200 hp rating! - Page 9

camarorat · 05-27-2009, 06:59 PM

The DS you are selling that can be used for the 10 or 12 bolt f body, is that a special order by you or is it the standard DS for the 12 bolt they sell?

Exotic Performance Plus · 05-29-2009, 05:27 AM

Quote:

Originally Posted by camarorat

The DS you are selling that can be used for the 10 or 12 bolt f body, is that a special order by you or is it the standard DS for the 12 bolt they sell?

It is the same length that PST can sell to anyone, for the 10 and 12 bolt. Thanks. Bob

KWIKKAR · 05-30-2009, 04:34 PM

Is the X dimension from the tranny seal or the metal part on the end of the transmission. Can't really tell from the pic.
thanks

camarorat · 05-30-2009, 05:13 PM

I was told its from the tranny seal to the center of the pinion U joint.

KWIKKAR · 05-30-2009, 06:08 PM

Quote:

Originally Posted by camarorat

I was told its from the tranny seal to the center of the pinion U joint.

Thank you

droksformula · 05-31-2009, 03:02 PM

Hi Bob, Im building my car to make around 900rwhp, would this pst 3.5' alum. shaft hold that or would you recomend the chromemoly or even there crazy carbonfiber driveshaft ? Thanks.

ZMONSTER! · 05-31-2009, 03:55 PM

I got one of these when I got my 9 inch, both from Bob here. The drive shaft is a beautiful piece that's for sure, and Im not worried about snapping or bending anything. My only complaint is that it came with no stickers for my garage sticker collage, nor was the one I got nearly as pretty as the one pictured in the first post.....

This is up there in the annals of injustice, right up there with the holocaust...

Ill make it though, somehow...

Exotic Performance Plus · 05-31-2009, 09:29 PM

Quote:

Originally Posted by droksformula

Hi Bob, Im building my car to make around 900rwhp, would this pst 3.5' alum. shaft hold that or would you recomend the chromemoly or even there crazy carbonfiber driveshaft ? Thanks.

It is the same one I use, it is rated at 1000 hp. You can see mine in this picture. Bob

Exotic Performance Plus · 07-30-2009, 06:05 AM

Bump for a great driveshaft. Bob

cookba · 07-30-2009, 08:49 AM

I'll be buying one of these really soon. are there any specific driveshaft loops that fit around this? I know my UMI DS loop is pretty tight around my stocker. thanks

Exotic Performance Plus · 07-31-2009, 05:57 AM

Quote:

Originally Posted by cookba

I'll be buying one of these really soon. are there any specific driveshaft loops that fit around this? I know my UMI DS loop is pretty tight around my stocker. thanks

Thanks. We usually take the BMR DS001 driveshaft loop and modify it to work. This driveshaft is only .25 larger on any side, so most loops will clear as long as they are centered on the driveshaft. Bob

cookba · 08-01-2009, 08:48 AM

How do you modify it? do you have a pic?

Exotic Performance Plus · 08-01-2009, 07:18 PM

Quote:

Originally Posted by cookba

How do you modify it? do you have a pic?

It took a little digging, but I found this picture from 2006. Bob

Exotic Performance Plus · 09-27-2009, 08:35 PM

Back to the first page. Bob

Engine_HP · 10-10-2009, 10:26 PM

Quote:

Originally Posted by Exotic Performance Plus

It is the same one I use, it is rated at 1000 hp. You can see mine in this picture. Bob