CAM IS SOLD!!

Stg 1 Exedy clutch. Never been installed. Comes with disk, PP, alignment tool and new bearing. **Does not include flywheel**. Completely stock driveability, rated to 400 rwhp. 275 SHIPPED

Here's a link for the clutch where my customer originally purchased.

http://cgi.ebay.com/ebaymotors/ws/eB...m=170123750872

Money orders preferred as this is being sold for my customer.

-Thanx

 

Any idea what the cam can do in a stock heads car with LS6 intake?

 

I cannot promise anything because I don't know the condition of your motor, but I wouldn't be at all suprised to see 410-415 rwhp w/ stock heads, a good tune and LS6 intake. The cam should make north of 400 rwhp on ANY setup with stock heads without much problem and LOTS of area under the curve (where power matters).

 

I'd call it a F13.5

With the intake of the F13 and Exhaust of a F14

Would take to spray very nicely!!!

 

Exactly

TTT

 

Motivated seller. No reasonable offer will be refused!

 

what would i need besides springs, lifters, retainers, and pushrods to make this cam work with stock heads 317 heads?

also will the clutch work with a 6.0 lq4 motor?

 

This is a great cam.

 

tttttttttttttttttttttttttttttttttttttttttttttttttt tttttttttttttttttttttttttttttttttttttttttttttttttt tttttttttttttttttttttttttttttttttttttttttttttttttt tttttttttttttttttttttttttttttttttttttttttttttttttt tttttttttttttttttttttttttttttttttttttttttttttttttt tttttttttttttttttttttttttttttttttttttttttttttttttt tttttttttttttttttttttttttttttttttttttttttttttttttt tttttttttttttttttttttttttttttttttttttttttttttttttt tttttttttttttttttttttttttttttttttttttttttttttttttt tttttttttttttttttttttttttttttttttttttttttttttttttt tttttttttttttttttttttttttttttttttttttttttttttttttt tttttttttttttttttttttttttttttttttttttttttttttttttt tttttttttttttttttttttttttttttttttttttttttttttttttt tttttttttttttttttttttttttttttttttttttttttttttttttt tttttttttttttttttttttttttttttttttttttttttttttttttt tttttttttttttttttttttttttttttttttttttttttttttttttt tttttttttttttttttttttttttttttttttttttttttttttttttt tttttttttttttttttttttttttttttttttttttttttttttttttt tttttttttttttttttttttttttttttttttttttttttttttttttt tttttttttttttttttttttttttttttttttttttttttttttttttt tttttttttttttttttttttttttttttttttttttttttttttttttt tttttttttttttttttttttttttttttttttttttttttttttttttt tttttttttttttttttttttttttttttttttttttttttttttttttt tttttttttttttttttttttttttttttttttttttttttttttttttt tttttttttttttttttttttttttttttttttttttttttttttttttt tttttttttttttttttttttttttttttttttttttttttttttttttt tttttttttttttttttttttttttttttttttttttttttttttttttt tttttttttttttttttttttttttttttttttttttttttttttttttt tttttttttttttttttttttttttttttttttttttttttttttttttt tttttttttttttttttttttttttttttttttttttttttttttttttt

 

no reply

 

Sorry man I must have skipped right over it. I didn't see it.

Sending you a PM..

 

ttttttt

 

what set of heads would be good for the cam?

 

sent you a PM

 

TEA's work very well with the Futral cams. If you want to take the next step up from the GM castings, then of course you have your Trick Flow & AFR options.

I've personally seen 440-470 rwhp with Futral's cams and TEA's heads.

All PM's replied to.

 

$300?

 

Just received paypal for the cam. It's been sold.

 

Is the clutch kit made for a LS1 or LS2 flywheel?

 

Ls1/ls6.

 

t5ttttttttttt