CHEAP: BMR LCAs, B&M Ripper, 7-Taylor T-volt wires, NEW Vette FRC (dual slots), K&N
Thread Starter
TECH Fanatic
iTrader: (17)
Joined: Mar 2006
Posts: 1,746
Likes: 2
From: West Chester, PA
CHEAP: BMR LCAs, B&M Ripper, 7-Taylor T-volt wires, NEW Vette FRC (dual slots), K&N Got a few things that Im looking to get rid of. Just tired of them sitting around.
1) SOLD!!!!! BMR Tubular Lower Control Arms. These are alittle rough...still nice and solid. They will need new bushings on both ends. BMR sells rebuild kits. See pics below. Ide like $25 o.b.o. shipped... SOLD!!!!!
2) SOLD!!!!! B&M Ripper. I never used this shifter in my DD...but I drove the car it came out of, and it seemed to work just fine. No shifter ****. Comes with the special washers and 4 bolts. Also comes with a boot...but its got a rip in it. Not sure how much use it would be for ya. Couple scratches here and there. Ide like $65.00 shipped.
3) SOLD!!!!! I have 7 Taylor Thundervolt Wires. The reason I have 7, is one fried on my header...stupid mistake on my part. These OHM out all the same and were working fine. I still have the bad wire somewhere...if you talk to Taylor, they might repair/replace it for you. Not sure where its at though. Ide like $20.00 shipped o.b.o. They wont come with the box...it'll be easier/cheaper to just ship the wires.
4) SOLD!!!!! Brand NEW Corvette fuel rail cover. Its the black with red lettering, and two slots. I bought this one, and decided to go with a single slot. I pulled it out just to take pictures...first time I opened it. Ide like $35 shipped o.b.o.
5) K&N cone filter. Its a universal. Has a stud on the end. Fits a 4" pipe, and is about 8.5"-9" long. I only used it for alittle while, then switched. Probably could use a cleaning...been stored in a box. $20.00 o.b.o. shipped.
All of these items are available for pick up. They are located in 19401. If you want, I can bring them to 19380...but you'd need to come get them between 12-1 during the week.
Email, PM, or respond here. Thanks!
Justin
jgindin20@hotmail.com
1) SOLD!!!!! BMR Tubular Lower Control Arms. These are alittle rough...still nice and solid. They will need new bushings on both ends. BMR sells rebuild kits. See pics below. Ide like $25 o.b.o. shipped... SOLD!!!!!
2) SOLD!!!!! B&M Ripper. I never used this shifter in my DD...but I drove the car it came out of, and it seemed to work just fine. No shifter ****. Comes with the special washers and 4 bolts. Also comes with a boot...but its got a rip in it. Not sure how much use it would be for ya. Couple scratches here and there. Ide like $65.00 shipped.
3) SOLD!!!!! I have 7 Taylor Thundervolt Wires. The reason I have 7, is one fried on my header...stupid mistake on my part. These OHM out all the same and were working fine. I still have the bad wire somewhere...if you talk to Taylor, they might repair/replace it for you. Not sure where its at though. Ide like $20.00 shipped o.b.o. They wont come with the box...it'll be easier/cheaper to just ship the wires.
4) SOLD!!!!! Brand NEW Corvette fuel rail cover. Its the black with red lettering, and two slots. I bought this one, and decided to go with a single slot. I pulled it out just to take pictures...first time I opened it. Ide like $35 shipped o.b.o.
5) K&N cone filter. Its a universal. Has a stud on the end. Fits a 4" pipe, and is about 8.5"-9" long. I only used it for alittle while, then switched. Probably could use a cleaning...been stored in a box. $20.00 o.b.o. shipped.
All of these items are available for pick up. They are located in 19401. If you want, I can bring them to 19380...but you'd need to come get them between 12-1 during the week.
Email, PM, or respond here. Thanks!
Justin
jgindin20@hotmail.com
Last edited by ghettocruiser; Jun 30, 2009 at 05:17 PM.
