Everyone,

This past holiday weekend was cleaning weekend for me at the house. All of these parts unless listed came off of my 02' TA with 40K unless otherwise noted. They were all in great working condition and were only removed because of me going to my FI'd 408 setup.

Anyways, all parts are OBO plus shipping, I'll figure shipping on a case by case basis.

I take paypal or money order or check or any form of currency that I can spend at the local store...not picky....pretty much whatever works for you.

Also, some of the parts may look a bit dingy, but I'll clean them up definitely before I send them out...just didn't have time this weekend. If you aren't satisfied with your parts after you get them, I'm am not a douche and will work with anyone to make it right. Now for the goodies...

Ported 78mm Throttle Body - $75

SOLD SOLD SOLD SOLD TO IGGY86

1997-2004 Corvette DBW Throttle Body - $60



MTI Clear Lid and K&N Filter - $80
SOLD SOLD SOLD SOLD TO 74Formula455

Stock Tranny Crossmember - $25



Complete AC Air Conditioning Setup (Brackets, Lines, Compressor, Belt, Condenser etc) - $250

SOLD SOLD SOLD SOLD TO HOTPOCKET

Descreened MAF and Bellow - $40

SOLD SOLD SOLD SOLD TO IGGY86

Stock Roller Lifters - $25
Previous CAM and springs were MTI X1 - 231/227 .591./.577 and had double springs on it good to .600







Electric Fans - EFans - $100
SOLD SOLD SOLD SOLD

FLP 1 3/4" Full Length Headers - $200
SOLD SOLD SOLD SOLD TO 96Sdime

3" ORY Off Road Y Pipe - $125

SOLD SOLD SOLD SOLD TO 96Sdime

Stock LS1 Radiator - $80
SOLD SOLD SOLD SOLD

Street & Performance LS1 Conversion Headers Into an OBS Chevy 88-98 2wd with Stainless bolts- $225 ($500 New - About 3000 miles on these)



NEW Treadstone FMIC Intercooler - $200



NEW EBAY FMIC Intercooler 31" x 12" x 4" - $120



Stock 10 Bolt Rear End With TA Support Girdle Cover (Works Great - No Noise) - $250 Local Pickup Only



Stock Radiator Overflow Tank - $25
SOLD SOLD SOLD SOLD IGGY86

 

Stock Fuel Lines and Misc equip - $15

SOLD SOLD SOLD SOLD TO 99Camaro.77

4L60E Transmission Heat Shield - $10



Stock Driveshaft - $65
SOLD SOLD SOLD SOLD

Stock Torque Arm - $30



Stock Bumper Core Support With Foam Uncut - $60



Anywho, that's whats up for grabs guys. I'm open to offers so ask away.

Thanks in advance for looking!

Cody B.

 

sent pm on lifters

 

I definately could use the overflow tank! Sending PM.

 

PM's Replied Guys.

Also, corrected the dimensions on one of the FMICs.

Thanks,

Cody B.

 

I'll take the lid and k&n for $80. I'll send you a pm.

 

PM's Replied!

 

PM's Replied!

 

Bump For Monday

 

pm sent on flp headers and y pipe

 

will buy the drive shaft for 50 to

 

Bump for the weekend....

Sale status' updated on all items!

And again, items are OBO, so don't be afraid to ask.

Thanks,

Cody B.

 

I'm interested in your A/C set-up.....I would need every component from the system though....is it all there?

 

Its all there except for the stuff under the dash, which I haven't touched yet and quite frankly am not sure what all is actually under there. I have available right now the Compressor, All lines, Drier (You'll need a new one when you install it, but the lines and bracket is there) Belt, Condensing Coil, and Block Mounting Bracket with tensioner.

I'll try and dig around to see whats under the dash that is essential for the rest of the kit.

Thanks,

Cody B.

 

What about the Evap core? Are you taking off the heater-A/C box from the firewall?

 

I'm interested in the radiator, I sent you a PM.

 

What size gears in the rear end?

 

It has 3.23 gears in it.

 

PM's Replied! Friday Morning Bump....only a handfull of things left!

Thanks,

Cody B.

 

BUmp for the last bit of stuff!