Complete 02' camaro drag car part-out
10-17-2009, 01:54 PM
#1
Launching!
Thread Starter
iTrader: (51)
Join Date: Feb 2006
Location: Port Orange/Daytona,Fl
Posts: 216
Likes: 0
Received 0 Likes
on
0 Posts
Complete 02' camaro drag car part-out I am parting out a like new combo for way of going a differnt route. All parts were purchased new and have less than 1000 miles of street use and maybe 15 track pass'. I am completely parting out the complete car. If it's not listed just pm me. All parts are to be picked up in the Daytona, Fl area or pay to have it shipped at your cost.
JW TH-400 ULTRA BELL, DEEP CAST PAN, MAN REV VALVE BODY WITH BRAKE ROLLERIZED BEARING SET 1000.00
STRANGE 12 BOLT REAR END SET-UP COMPLETE 3.42 GEAR SET, T/A REAR COVER, 1350 BILLIT PINION, TRUE TRAC, 33 SPL AXLES, WAS SET UP AS A 4 CH REAR BUT NOW HAS A STRANGE DRAG BRAKE SET-UP ON IT,IT IS 1" SHORTER ON EACH SIDE, HAS THE BMR EXTREME SWAY BAR BRACKETS WELDED TO IT ALONG WITH THE BMR CONTROL RELOCATION BRACKETS , IT'S PAINTED NICELY IN EMERON BLACK PAINT, WILL ALSO COME WITH A CUSTOM MADE STEEL DRIVESHAFT TO GO TO A TH-400 TRANS 2600.00
STRANGE S5270 REAR SINGLE ADJ. SHOCKS 200.00 PR ( SOLD )
STRANGE S 5271 FRONT SINGLE ADJ. STRUTS WITH SPRINGS 300.00 PR ( SOLD )
STRANGE MAN. BRAKE MASTER CYL CONVERSION SET-UP 150.00 ( SOLD )
STRANGE B4180WC FRONT DRAG BRAKE SET-UP WITH LINES 600.00 ( SOLD )
BMR KM003 K-MEMBER FOR LS1 CAR WITH FACTORY POWER RACK 375.00
BMR XTA001 EXTREME TORQUE ARM 500.00
BMR XSB001 EXTREME REAR SWAY BAR SET-UP WILL NEED NEW AXLE BRACKETS FROM BMR. THEY ARE LIKE 35 FOR THE KIT 350.00
BMR TCCOO1 LS1 CAR TO TH-400 TRANS MOUNT 100.00 ( SOLD )
BMR RS001 POLISHED RAD SUPPORT 60.00 ( SOLD )
BMR ADJ. FRONT LOWER CONTROLL ARMS 275.00 ( SOLD )
BMR FIXED UPPER CONTROLL ARMS 155.00
KOOKS 1 7/8 TO 2" STEP HEADERS, STAINLESS 700.00 ( SOLD )
ALSO HAVE A CUSTOM STAINLESS 3.5" TO 4" ROUND MAGNAFLOW MUFFLER THAT CAN BE PURCHASED TO MAKE THIS A BOLT-ON SET-UP 400.00
ALSO HAVE COMPLETE TAN CLOTH INTERIOR. LET ME KNOW WHAT YOU NEED, I HAVE A COMPLETE CAR TO TEAR DOWN. ALL PARTS ARE STILL ON CAR.
JW TH-400 ULTRA BELL, DEEP CAST PAN, MAN REV VALVE BODY WITH BRAKE ROLLERIZED BEARING SET 1000.00
STRANGE 12 BOLT REAR END SET-UP COMPLETE 3.42 GEAR SET, T/A REAR COVER, 1350 BILLIT PINION, TRUE TRAC, 33 SPL AXLES, WAS SET UP AS A 4 CH REAR BUT NOW HAS A STRANGE DRAG BRAKE SET-UP ON IT,IT IS 1" SHORTER ON EACH SIDE, HAS THE BMR EXTREME SWAY BAR BRACKETS WELDED TO IT ALONG WITH THE BMR CONTROL RELOCATION BRACKETS , IT'S PAINTED NICELY IN EMERON BLACK PAINT, WILL ALSO COME WITH A CUSTOM MADE STEEL DRIVESHAFT TO GO TO A TH-400 TRANS 2600.00
STRANGE S5270 REAR SINGLE ADJ. SHOCKS 200.00 PR ( SOLD )
STRANGE S 5271 FRONT SINGLE ADJ. STRUTS WITH SPRINGS 300.00 PR ( SOLD )
STRANGE MAN. BRAKE MASTER CYL CONVERSION SET-UP 150.00 ( SOLD )
STRANGE B4180WC FRONT DRAG BRAKE SET-UP WITH LINES 600.00 ( SOLD )
BMR KM003 K-MEMBER FOR LS1 CAR WITH FACTORY POWER RACK 375.00
BMR XTA001 EXTREME TORQUE ARM 500.00
BMR XSB001 EXTREME REAR SWAY BAR SET-UP WILL NEED NEW AXLE BRACKETS FROM BMR. THEY ARE LIKE 35 FOR THE KIT 350.00
BMR TCCOO1 LS1 CAR TO TH-400 TRANS MOUNT 100.00 ( SOLD )
BMR RS001 POLISHED RAD SUPPORT 60.00 ( SOLD )
BMR ADJ. FRONT LOWER CONTROLL ARMS 275.00 ( SOLD )
BMR FIXED UPPER CONTROLL ARMS 155.00
KOOKS 1 7/8 TO 2" STEP HEADERS, STAINLESS 700.00 ( SOLD )
ALSO HAVE A CUSTOM STAINLESS 3.5" TO 4" ROUND MAGNAFLOW MUFFLER THAT CAN BE PURCHASED TO MAKE THIS A BOLT-ON SET-UP 400.00
ALSO HAVE COMPLETE TAN CLOTH INTERIOR. LET ME KNOW WHAT YOU NEED, I HAVE A COMPLETE CAR TO TEAR DOWN. ALL PARTS ARE STILL ON CAR.
Last edited by Mr.Nitrous; 10-25-2009 at 12:59 PM.
10-17-2009, 02:18 PM
#4
Launching!
Thread Starter
iTrader: (51)
Join Date: Feb 2006
Location: Port Orange/Daytona,Fl
Posts: 216
Likes: 0
Received 0 Likes
on
0 Posts
http://www.bmrfabrication.com/Brakes/Strange1.jpg
Thats what they are. I need to get a camera to take pics and pull the wheels off also.
Thats what they are. I need to get a camera to take pics and pull the wheels off also.
Trending Topics
10-18-2009, 01:41 PM
#17
Launching!
Thread Starter
iTrader: (51)
Join Date: Feb 2006
Location: Port Orange/Daytona,Fl
Posts: 216
Likes: 0
Received 0 Likes
on
0 Posts
The brake kit is a bolt on set-up. All that needs to be done it make the connection from the factory hard line to the braided ss lines. I'll throw in the lines to the calipers too, they don't come with the kit. Prob about 30/40 in shipping
