I'm starting to part my car out so I have a ton of parts and I will be adding more down the line and pics will be posted soon

Fuel system:
Lonnies performance double pumper kit/wiring harness, includes two in-tank walbro 340's. The secondary pump is activated via a hobbs switch under boost. The primary and secondary pumps are easily switched by swapping plugs by the alternator. SOLD
Braided stainless steel -8/-6 feed/return lines (black/polished fittings) with aeromotive 12301 filter and aeromotive quick disconnect fittings to connect to the oem lines coming off the tank. SOLD

Alcohol injection systems Stage 2 Adjust. Progressive Trunk Mount Water Methanol Injection System with upgraded dual nozzles and braided stainless line. SOLD

Drivetrain:
Mcleod sfi approved lt1 bellhousing SOLD
Pst 3.5" aluminum driveshaft with 9" u joint (1350 i believe) SOLD
Pro 5.0 short throw shifter SOLD

Suspension: Everything is red in color
Bmr tubular upper a-arms SOLD
Bmr tubular lower a-arms SOLD
Bmr tubular k-member SOLD
Bmr adjustable torque arm SOLD
Bmr torque arm relocation bracket (chassis mount instead of trans mounted) SOLD
Bmr adjustable lower control arms SOLD
Bmr adjustable panhard rod SOLD
Bmr driveshaft loop SOLD
Qa1 single adjustable f series shocks front/rear with 300lb front springs SOLD

Autometer ultra light 2 5/8 boost gauge SOLD
Autometer ultra light 2 1/16 digital/electric fuel pressure gauge SOLD

Msd 6al-2 ignition box with built in rev limiter and 2 step SOLD
Meziere heavy duty electric water pump SOLD
Bbk 52mm throttle body $220

Forged 355 ci, built by speed inc. Eagle crank, h beam rods, diamond pistons, Canton 7 qt oil pan, 216/222 114+4 .560/.560 (custom blower grind), lt4 timing chain, lt4 intake port matched to heads, lt4 heads cnc ported, pro magnum 1.6 rockers, 8.75:1 compression ratio with a hair under 10,000 miles total.
Inake to oil pan, for $3300 or your stock motor plus cash. Any questions just ask!
This setup made 755/747 on 91 octane with methanol.

All prices are obo plus shipping so if there is something you might be interested in shoot me a pm.

 

are you going a different route now ? i remember seeing pics of the procharger install

 

I'm going back to stock so I can sell it. I've had a zo6 in my mind for awhile now, so thats what i'm goin after.

 

pm sent!

 

Hey, I would like to buy alot of your parts what kinda deal can you give me for the upper and lower a arms, k frame, bellhousing and pst driveshaft shipped to 98230 WA. Please let me know your price shipped for all of these items as I would like to buy them all if we can work out a deal. Payment awaiting.

Thanks a lot
Ryan

 

How much plus stock motor? I've got a 97 z with 120k lt1

 

for sure interested in the panhard bar and the lower contol arms! shoot me and email at zachtower@yahoo.com

thanks!

 

All pm's should be replied to!
Letsrun, I could do $2800/your motor plus shipping if its in good running condition.

 

alright good luck with the z06

 

Did you run an intercooler or just a meth kit? Do you have pics of the kit installed?

 

Lca's are sold!

Evaporate-I ran both. I have a pic of where I had the nozzles mounted but thats it. I had the tank mounted in the driver side quarter panel and the controller in my center console.

 

Bump!

 

Qa1's are sold.

 

Pro 5.0, bellhousing, torque arm and relocation bracket sold pending payment.

 

Torque arm, relocation bracket, bellhousing and pro 5.0 are sold.

 

Bump for all new prices.

 

Bump!

 

Fuel lines and fuel pressure gauge are sold!

 

Upper and lower A arms are sold!

 

Msd is sold!