Category: Racing Parts
Price: $1
Part Fits: 93-02 Chevrolet Camaro, 93-02 Pontiac Firebird
Location (State): IL
Item Condition: Used
Shipping Information: Item Can be Shipped
Engine: LS1/LS6
LS Engine?: Fits LS Engine

I finally got my car running, and cleaned up the garage. I have tons of stuff i would like to get rid off.
All parts off the car are from a 98 6spd trans am. All prices are picked up. IF you would like the item shipped buyer to pay actual shipping.

just added 317 heads, with valves, and springs. There is some damage to 1 of the heads. machine shop could fix, but i went with a newer ported head. I included tons of pictures below so buyer knows exactly what you are getting. If you are intereted in heads i have hi res pics as well. To ship the heads will be atleast 50 dollars. I will take 150$ shipped, or 100$ picked up. 100 Shipped!

Stock ls1 rockers with hardware. 45$ shipped. 30 Shipped!



Alum Ls1 driveshaft with 1350 u joint(i had a mwc fab9) 120 shipped$100 Shipped!

Ebay centerbolt valve covers, Alum, with bolts. no gaskets. -10 alum bungs welded in center of each one. These valve covers have no mounts for coil packs.(so you will have to relocate them, or come up with something)
They are also powder coated black. Some people have problems with these valve covers leaking. I did, untill somone on tech told me to push up on them while you tighten them up. I have over 350 into these valve covers, i will let them go for 200 shipped!175 Shipped!





K&n 7inch cone filter. 3 inch inlet. used on my turbo for a short while. 20$


rear calipers.(no brake lines, both work pefectly) Best offer$


Driver Airbag. Best offer$


Passanger air bag. Best offer$


Working ls1 maf.(started porting, never finished) 50$


th400 trans pan.(stock truck pan, deep) 20$



Power driver seat. Works great. Small tear in normal spot from normal wear and tear. Best offer$


Backseat in great condition. Best offer$



The last item for sale is a rear sway bar off my 98 trans am. it was on the car when i got it. I dont know what brand it is. It is red powdercoated. $75




FUELAB 515 Series Fuel Pressure Regulator (FPR) Fuel lab part number is 51502-C-BLK. It has 2 -6 inlets, and 1 -6 return. This regulator is 130 dollars new, from the cheapest places online. Plus you need -6 male o ring to -6 male fittings, I have all 3 already installed. So 130 dollar regulator, and 30 dollars in fittings. Has gauge port, this regulator is not boost referenced. It is all black, and new. I installed, but never used.Will sell for 100 shipped, with fittings. 85 Shipped!





I will do my best to add as many pictures as i can over the next couple days.

Thanks, Chris

 

Valve covers sale pending!
Driver seat sale pending!
8 msd wires sold! Thank you
7 plug wires sold! Thank you.
Panhard bar sold! Thank you.
K&N lid sold! Thank you.
Clutch Master sold! Thank you

 

 

how much for the adj panhard bar shipped to 35613

 

sent you a pm.

Thanks, Chris

 

Are the bungs in the valve covers for PCV?

 

p.m'd. on the K&N lid air cleaner ....

 

Paid and included extra to cover paypal fee's let me know when its ("K&N LID air filter") on the way . Thx u!
Michael

 

I run them to catch cans, so yes... Added a very nice fuel lab regulator to listing. All pm's are replied to.

Thanks, Chris

 

have you shipped the panhard bar yet?

 

Yes, it went out his morning via ups. I will pm you the tracking number.

Thanks, Chris

 

Bump.

 

ill do 30 shipped on the msd if you guarantee they all ohm out good.

 

I can check them with a meter, what are they supposed to ohm to. If there all good, ill do 35 shipped

 

I can do 125.00 shipped to 36693 on the covers
mike

 

Set of msd wires ohm out to about 35-38 ohms. Its hard to get exact readings, but they were all right around there.

According to msd the wires are 45-50 ohms per foot. So they appear to be in the right area. None of the boots are burned.

Thanks, Chris

 

Updated listings with stuff sold, and sales pending. Lowered prices, and added some shipped prices!

Thanks, Chris

 

Please measure the diameter of the rear swaybar please.

 

I wont be home till tuesday evening, i will let you know

 

22.6 mm. Let me know

Thanks, Chris