LT1 engine parts for sale!!
#1
LT1 engine parts for sale!!
Due to bills, I am parting out un needed engine parts and possibly more but for right now I have 3 things. Pay Pal is accepted, prices included shipping in the U.S.
1) Crane Fireball HI-6S Ign Box w/ Harness & Coil: EXCELLENT CONDITION!
this is practically brand new. There are no issues with 92-95 LT1's, below is a link from a GMHTP artical mentioning a crank trigger may be needed but that would be it.
http://www.gmhightechperformance.com...1htp_ignition/
One cool feature when you run n2o is if you couple the unit with the TRC-2 timing retard box you can set it up for instant ignition retard when the selinoids open up.
The comes with the coil, ignition box, and plug in and play harness for the coil so no splicing needed. Fits nice and neat.
I accept pay pal, or cert bnk check
email blkscreaminmach@hotmail.com or pm here.
*pics*
http://www.mainstreamtopics.com/~scr...0Ign%20Box.JPG
http://www.mainstreamtopics.com/~scr...%20harness.JPG
Also to mention there are also other functions that you can hook up a aftermarket tach, proportional timing retard vs. boost, rev limiter. The harness for the coil is not normally included and the price is the shipped price with in the US.
PRICE: 150.00$
2) UD pulley, nothing extra needed!!
What I am selling is a Under Drive Pulley, with proper length serp belt and Proper length bolts.
I used this on a stock ALT pulley and had less then 1/2" deflection. I took it off last year and was planning on putting it back on but bills are forcing me to sell everything.
These Aeromotive LT1 billet aluminum crankshaft pulleys are made from billet CNC-machined 6061-T6. They are engineered to reduce accessory loads and increase rear-wheel horsepower for your vehicle. These are 34 percent underdrive pulleys with a hand-polished finish to dress up your engine's belt system and allow for easy cleaning. Mounting hardware is included.
This is what I found on summit racing.
Pay Pal is accepted
blkscreaminmach@hotmail.com
PRICE: 40$ shipped
Click here for pic
http://www.mainstreamtopics.com/~scr...D%20pulley.JPG
3) 58MM BBK TB w new/slotted TPS sensor
This piece is in excellent condition. Most people say you only need 52mm, but nothing can hurt you by going bigger. Especially for the larger cube/forced induction setups.
http://static.summitracing.com/globa...e/bbk-1534.jpg
This has a brand new GM TPS sensor, slotted and yeilds roughly 0.68 volts at idle.
PRICE: $250.00
1) Crane Fireball HI-6S Ign Box w/ Harness & Coil: EXCELLENT CONDITION!
this is practically brand new. There are no issues with 92-95 LT1's, below is a link from a GMHTP artical mentioning a crank trigger may be needed but that would be it.
http://www.gmhightechperformance.com...1htp_ignition/
One cool feature when you run n2o is if you couple the unit with the TRC-2 timing retard box you can set it up for instant ignition retard when the selinoids open up.
The comes with the coil, ignition box, and plug in and play harness for the coil so no splicing needed. Fits nice and neat.
I accept pay pal, or cert bnk check
email blkscreaminmach@hotmail.com or pm here.
*pics*
http://www.mainstreamtopics.com/~scr...0Ign%20Box.JPG
http://www.mainstreamtopics.com/~scr...%20harness.JPG
Also to mention there are also other functions that you can hook up a aftermarket tach, proportional timing retard vs. boost, rev limiter. The harness for the coil is not normally included and the price is the shipped price with in the US.
PRICE: 150.00$
2) UD pulley, nothing extra needed!!
What I am selling is a Under Drive Pulley, with proper length serp belt and Proper length bolts.
I used this on a stock ALT pulley and had less then 1/2" deflection. I took it off last year and was planning on putting it back on but bills are forcing me to sell everything.
These Aeromotive LT1 billet aluminum crankshaft pulleys are made from billet CNC-machined 6061-T6. They are engineered to reduce accessory loads and increase rear-wheel horsepower for your vehicle. These are 34 percent underdrive pulleys with a hand-polished finish to dress up your engine's belt system and allow for easy cleaning. Mounting hardware is included.
This is what I found on summit racing.
Pay Pal is accepted
blkscreaminmach@hotmail.com
PRICE: 40$ shipped
Click here for pic
http://www.mainstreamtopics.com/~scr...D%20pulley.JPG
3) 58MM BBK TB w new/slotted TPS sensor
This piece is in excellent condition. Most people say you only need 52mm, but nothing can hurt you by going bigger. Especially for the larger cube/forced induction setups.
http://static.summitracing.com/globa...e/bbk-1534.jpg
This has a brand new GM TPS sensor, slotted and yeilds roughly 0.68 volts at idle.
PRICE: $250.00
#2
feel free to contact me blkscreaminmach@hotmail.com OR PM here! Also my Pay pal is the same email address
Last edited by BlackScreaminMachine; 06-16-2006 at 03:14 PM.