FS: Turbo Parts, Silicone, Catch can, Vband clamp, Manley Springs, and MTI Clear Lid
Thread Starter
TECH Fanatic
iTrader: (9)
Joined: Apr 2005
Posts: 1,395
Likes: 0
From: ATL/Savannah Georgia
FS: Turbo Parts, Silicone, Catch can, Vband clamp, Manley Springs, and MTI Clear Lid Left over stuff that I won't be needing from my setup. Received from another member that shipped the wrong parts but won't allow a return, so its selling cheap.
Selling all the turbo stuff together good for DIY turbo or FMIC: SOLD
-Catch can w/breather, fittings and tubing
-2.5" Pipes (2 45* pieces and straight piece w/ BOV flange)
-Filter with shield (has silicone reducers inside to fit any size pipe) Dirty needs spray down with recharge kit
-Silicone Couplers (long 2.5"(2), (1) 2.5" elbow, (2) short 2.5") Clamps included
-A pillar guage holder (does NOT include boost guage)
-Sunpro vacuum tubing with fittings (new)
MTI Clear Lid with KN filter (good condition in original box):
(usually $150+ for clear lids plus $45 for filter) will sell for SOLD
New 3" V-band clamp (just the clamp): SOLD
Manley 221423 Nextek Springs w/ retainers:
($210 new + cost of retainers) will sell for SOLD
PM me with any questions. Paypal only. Thanks
-Jason
Lid and Filter pics are linked below the others
Selling all the turbo stuff together good for DIY turbo or FMIC: SOLD
-Catch can w/breather, fittings and tubing
-2.5" Pipes (2 45* pieces and straight piece w/ BOV flange)
-Filter with shield (has silicone reducers inside to fit any size pipe) Dirty needs spray down with recharge kit
-Silicone Couplers (long 2.5"(2), (1) 2.5" elbow, (2) short 2.5") Clamps included
-A pillar guage holder (does NOT include boost guage)
-Sunpro vacuum tubing with fittings (new)
MTI Clear Lid with KN filter (good condition in original box):
(usually $150+ for clear lids plus $45 for filter) will sell for SOLD
New 3" V-band clamp (just the clamp): SOLD
Manley 221423 Nextek Springs w/ retainers:
($210 new + cost of retainers) will sell for SOLD
PM me with any questions. Paypal only. Thanks
-Jason
Lid and Filter pics are linked below the others
Last edited by JAvenger007; Apr 28, 2007 at 10:27 AM.
Trending Topics
Thread Starter
TECH Fanatic
iTrader: (9)
Joined: Apr 2005
Posts: 1,395
Likes: 0
From: ATL/Savannah Georgia
Its just a single one that goes over your existing pillar. I believe you can screw it in or use adhesive. I never installed it so im going off of what the website says.
davidfre21 only difference is the IAT sensor. This lid has a provision for it but you can plug it depending on whether you need it or not. They all fit the same. Ive got two others lined up for it though and that price is pretty locked. ill let you know if they both happen to fall through.
up top, thanks for interest guys
davidfre21 only difference is the IAT sensor. This lid has a provision for it but you can plug it depending on whether you need it or not. They all fit the same. Ive got two others lined up for it though and that price is pretty locked. ill let you know if they both happen to fall through.
up top, thanks for interest guys
interested in the turbo fittings, i may be putting a fmic on my ws6 soon. are all the parts in the attached picture that says not for sale on it? just interested in the tubing parts if you want to sell the pod separate.
