Torquer V2 Idle Vid clip
08-13-2007, 08:28 PM
#3
11 Second Club
Thread Starter
iTrader: (23)
Join Date: May 2003
Location: Eugene OR
Posts: 295
Likes: 0
Received 0 Likes
on
0 Posts
the car is loud as hell now with the cam, I actually think the rasp is less since the swap, overall the sound while much louder is alot meaner : )
08-13-2007, 08:30 PM
#4
11 Second Club
Thread Starter
iTrader: (23)
Join Date: May 2003
Location: Eugene OR
Posts: 295
Likes: 0
Received 0 Likes
on
0 Posts
Heres a clip punching it at 15mph until about 65
And before anyone says anything, yes I know its a school zone, its right by my house and it was after 6pm in the summer and there was no one around, I wouldnt drive that fast by there when schools in session
And before anyone says anything, yes I know its a school zone, its right by my house and it was after 6pm in the summer and there was no one around, I wouldnt drive that fast by there when schools in session
08-13-2007, 10:16 PM
#6
11 Second Club
Thread Starter
iTrader: (23)
Join Date: May 2003
Location: Eugene OR
Posts: 295
Likes: 0
Received 0 Likes
on
0 Posts
We dont have any dynos close to here : (
I am more interested in track times, I will hopefully get some runs in over the next few weeks
I am going to ditch the ory and put some highflow cats on it over the winter both to make it easier to get inspected and hopefully quiet it down a little : )
I am more interested in track times, I will hopefully get some runs in over the next few weeks
I am going to ditch the ory and put some highflow cats on it over the winter both to make it easier to get inspected and hopefully quiet it down a little : )
Trending Topics
08-25-2007, 10:18 AM
#9
Restricted User
iTrader: (18)
Join Date: Apr 2007
Location: Fayetteville, NC
Posts: 1,515
Likes: 0
Received 0 Likes
on
0 Posts
more videos!!! I wanna see more. I'll be installing my torquer 2 here soon and I have a the same exhause setup as you + an electric cutout. Post up more vids!!!
08-26-2007, 02:44 PM
#11
ur car sounds very nice with the magnaflows.
i have the same cam and almost the same mods that this guy has and i run a 12.71@115mph with a crappy driver.
Originally Posted by BayAreaSS
Sounds good.
I'm interested in this cam. I would like to see what you run at the track
I'm interested in this cam. I would like to see what you run at the track
08-26-2007, 08:06 PM
#13
11 Second Club
Thread Starter
iTrader: (23)
Join Date: May 2003
Location: Eugene OR
Posts: 295
Likes: 0
Received 0 Likes
on
0 Posts
Originally Posted by bad6as
fyi this cam has 9* of overlap
232/234 112 right?
232/234 112 right?
yes sir, and it ran 12.8s before the cam and stall so I am hoping for low low 12s / high 11s now
08-26-2007, 08:40 PM
#14
11 Second Club
Thread Starter
iTrader: (23)
Join Date: May 2003
Location: Eugene OR
Posts: 295
Likes: 0
Received 0 Likes
on
0 Posts
as far as driveability with this cam other than hunting for idle the first min or two upon start up its fine................
I hear it wont like the cold weather but I put it away about late Oct until late April so its really not an issue for me
I hear it wont like the cold weather but I put it away about late Oct until late April so its really not an issue for me
08-26-2007, 09:00 PM
#16
11 Second Club
Thread Starter
iTrader: (23)
Join Date: May 2003
Location: Eugene OR
Posts: 295
Likes: 0
Received 0 Likes
on
0 Posts
1st gear rolling at about 15mph I punched it, stayed into it until about 60, didnt want to **** the neighbors off too much, you can hear me let off at the end
just goosing the throttle at idle, it breaks the Mickey Thompsons loose with little effort, before its recent mods it would only break em loose by power brakeing it
I have a shitty camera that only takes like 15 second clips and the sound quality isnt great but its all I got
08-26-2007, 11:08 PM
#17
On The Tree
Join Date: Jul 2007
Location: Borger,TX
Posts: 146
Likes: 0
Received 0 Likes
on
0 Posts
another idea just a suggestion i may offer for those of u who r lookin at gitting a cam......i just got done installing and dynoing the Torquer V.3 in my M6 02 T/A it's cam is awesome tomorrow i plan on making new video clip of it running since i got it tuned.....and i got copy of dyno charts if any of u r interested in them.....just tryin to throw some more options out there for u
08-28-2007, 10:14 PM
#19
11 Second Club
Thread Starter
iTrader: (23)
Join Date: May 2003
Location: Eugene OR
Posts: 295
Likes: 0
Received 0 Likes
on
0 Posts
just fyi these clips are with a zo6 maf that the car was not tuned for, I have a stock one on there now and it idles a little smoother and seems to pull harder, I will get new vids in a week or so
08-29-2007, 12:35 AM
#20
TECH Veteran
iTrader: (10)
Join Date: May 2006
Location: Bay Area, CA (Pittsburg)
Posts: 4,240
Likes: 0
Received 2 Likes
on
2 Posts
Originally Posted by CaliboyTA
ur car sounds very nice with the magnaflows.
i have the same cam and almost the same mods that this guy has and i run a 12.71@115mph with a crappy driver.
i have the same cam and almost the same mods that this guy has and i run a 12.71@115mph with a crappy driver.