pro2low

iTrader: (3)

i recently installed one and reach my goal for the power i wanted which was 400rwhp cam only....wha have you guys made with this cam? im thinkin i should have gone bigger haha.

Dragkid1917

iTrader: (2)

what else u have done? i made 375 with stock ls1 intake and tb, and no ud pulley. in 77 degrees. What was your TQ. Oh and im A4

pro2low

iTrader: (3)

m6, bolt ons and headers.......torque was about 380 i think......and it was over 95 degrees in the shop that day haha

ifit was a colder day would it make much of a difference?

pro2low

iTrader: (3)

oh yea haha my injectors are at 95% of their duty cycle now too!

SSwt00SS

iTrader: (18)

how about some video of how your car sounds...i have a TSP 231/237 im waiting to install after i max out my little 224 cam that's in the car now...

pro2low

iTrader: (3)

i dont have any video of it i will try and get some and get it up on here.......i could get a clip of it idling up in a little bit but no beating on it yet haha.

LSInnovations

iTrader: (7)

442 rwhp SAE through A4 with 233/239 TSP /w TSP LS6 heads.

pro2low

iTrader: (3)

i cant find the charger for my camera right now!

zheiling

Don't expect huge numbers then you won't be dissappointed. I did. I only made 362hp and 345tq. The guy running the dyno said their dyno shows 10hp less than others though. I had a stock lid though. Since then I have upgraded to an slp lid and a k&n filter. So I would say about 370-375hp and 350-360 tq. I am thinking my tune is off a little so you will probably make a little more if your tuner is good.

pro2low

iTrader: (3)

anybody else have any sound clips of theirs?

99_Z_155

iTrader: (7)

I Have That Cam. I Made The Same Numbers, About 375 With Stock Heads And Intake. That Cam Loves The Nitrous Though. Put Down 503tq With A 125 Shot. It Was Around 100 Degrees With The 375 Number. To Make The 400 Number You Just About Have To Have The Ls6 Intake Or Better. Heads Are Great Too, But I Dont Have The Cash Like Most.

ricketzSS

iTrader: (8)

Here is a vid of mine, on a 113lsa through LT's ORY and dual/dual
http://www.youtube.com/watch?v=fY2VNM8559E

pro2low

iTrader: (3)

sounds good mine is a little lopey'er my idle is at 1000 rigt ow i want it to be at 800

Ricks99ls1

iTrader: (9)

I AM GOING TO BE INSTALLING THIS CAM NEXT WEEK, WHAT DO YOU GUYS THINK, ILL PUT DOWN, I AM GOING WITH THE UNDERDRIVE PULLEY ASWELL, also i am a m6 should i get a 112 lsa? any help would appreciate, not trying to hijack pro2plow

Dragkid1917

iTrader: (2)

i made 374 with mine. No pulley, and LS1 intake/Tb. As for rick, i would say first off hold you ears on the dyno my car was so loud with that exaust even the dyno guys were like, thats rediculus. I would say.... 395 h/p through the M6, polished tb and the ud pulley. The 180 degree thermo might hold a few horses back over the 160...

MAX12421

Mine is in but, no numbers yet.. I'll try to get a video tomorrow.

ricketzSS

iTrader: (8)

It depends how much lope u want. I wish i would have went with the 112 but then again i have the dual/dual so its quieter then your LM1. A 113 Through the loud mouth it could be alot louder then mine. But i know through my cutouts it sounds ridiculous, it sets off car alarms just cruisin around. The 112 is going to give you some more tq, cuz this cam isnt all the torquey, it really kicks in at about 4k.

151ls1

iTrader: (1)

My car only made 351 rwhp/354 rwtq. This was on a conservative mustang dyno though. I think I would've seen better numbers on a dyno-jet. Also the pulls were only made to 6000 rpm and car is an A4.
Here is my dyno sheet:
Dyno sheet
Here's a couple quick idle clips (untuned):idle vid
idle vid 2

Dragkid1917

iTrader: (2)

oh my car made its power at 6600 rpm.... 6000 wnt show good numbers

Ricks99ls1

iTrader: (9)

i want it to obviously be noticeable, but not rediculous, also i wont drive this car everyday, but when i do i want it to be able to drive well, anyone have any sound clips on a 112 lsa?