***** MOST PRICES REDUCED *****

I have a 408 For Sale with only Dyno time on it. This motor made 648 HP on 93 Octane Pump Gas. NO NITROUS. On a engine Dyno.

Here are the specs:
408ci iron block
6.0L block
Eagle Forged LS1 Crank 4" Stroke
Callies LS1 Rods
Diamond Custom Pistons -2cc With High Temp Coating good for over 400 HP of Nitrous
Diamond Pro-Select Rings
Federal Mogul Main Bearings
Federal Mogul Rod Bearings
Dura Bond Cam Bearings
ARP Main Studs
ARP Head Studs
CamMotion HYD. Roller 249/257 650/650 lift on a 114 for the Juice
GM High Performance roller lifters with retaining trays
Cometic Head Gaskets
SDPC Heavy Duty Cam gears with Single Chain
Ported and Polished LS6 Oil Pump and pick up tube
Front and Rear covers
F-Body pan
Comes with GM Cam and Crank sensor
Short block fully balanced, blueprinted and assembled
Compression was 11.7 to 1 with my 243 heads.

I have $5000 in this setup
I am asking SOLD

LS6 CUSTOM PORTED 243 HEADS
These are the heads off of the above shortblock. They have dyno time only. They have 2.05/ 1.6 Rev Valves with Patriot Dual springs installed. They were ported by M2 Race Systems in New Jersey to Absolute Speed's Spec's.

They Flow 324 Intake and 212 exhaust @ 600 lift but the exhaust flow better with a 1 3/4 pipe on them. Comes with Comp hardened Pushrods. I have over $1600 in the head setup.
I'm asking SOLD

4l60E Stage 3 Transmission with Less than 1000 miles on it. Full of good parts. Shifts crisp.
I'm asking SOLD

Fuddle 3600 Torque converter also with less than 1000 miles
I'm askig SOLD

3 1/2 Aluminum driveshaft for a F-Body with a TH-400 and a 12 Bolt
New it cost over $430
I'm asking SOLD

BMR TH400 Torque Arm Relocation and Crossmember. Part # TCC010.
I'm asking SOLD

Ford Racing 42# Inj. Brand New never used. 8Pcs.
I'm asking SOLD

Aeromotive FP Regulator Part # 13101 Barely used.With Autometer FP Gauge.
I'm asking SOLD

Paxton FP Regulator. Similar to Aeromotive Part # 13203. Barely used.
I'm asking $100 Shipped


Harris Speedworks Interface Nitrous Controller.
http://www.harrisspeedworks.com/shop...age=1&featured Slightly used. SOLD


1999-02 A4 F-Body under hood Engine Harness with stock computer.
I'm asking SOLD

1998 M6 F-Body under hood Engine Harness with 98 Stock Computer.
I'm asking $230 shipped

***** ALL ABOVE PRICES ARE BEST OFFER. I HAVE SOLD MY CAR AND THESE ARE LEFT OVER PARTS THAT MUST GO. SO DON'T BE AFRAID TO PM ME AN OFFER. ALSO THE ABOVE SHIPPING PRICES ARE FOR THE 48 STATES ONLY. IF YOU LIVE ELSEWHERE THAN ADDITIONAL SHIPPING CHARGES MAY BE APPLIED. PAYPAL WILL BE ACCEPTED. *****

Pics for the above parts will be added tonight.
NO DIBS. FIRST TO PAY GETS THE PARTS.

 

HERE IS LINK TO THE PICS:

http://s264.photobucket.com/albums/i...20408%20PARTS/

 

where did u buy the 4l60e whats the best deal u can do on it

 

It came out of my car. PM me an offer. You never know.

 

Who built the tranny? What parts are in it? What do they consider their stage 3 to hold for hp and tq levels???

 

Built by JR transmissions in TX. Has a high performance servo kit, good clucthes and steels, high performance shell and band. 650 hp and Tq.

 

Is the engine still together??

 

The engine is apart. But I can reassemble the heads back to the exact state that it was in for the dyno. I just removed the heads to show the condition of the shortblock. Which is Mint.

 

Obo Guys.

 

Oh man I wish this motor will still be availalbe in a couple months. . I doubt it will be but a guys can wish...

 

Who built the motor?

 

FORCED FED HIGH PERFORMANCE. I was one of the lucky ones that got a shortblock out of them before they went out of business. So when I received it, we checked every part and all clearances to make sure that the shortblock was put together with all the right parts correctly.

***** MOST PRICES REDUCED *****

 

pm sent

 

good deal on the heads wish they had 2.08 valves

 

Prices Reduced Again ! Everything Must Go !

 

Hey man just wondering if you still had it? Also is there anything wrong with it? Triple disc? What str? Do you have a receipt or a card or anything on it? Let me know i may be interested.

 

PM SENT

 

STILL GOT SOME GREAT PARTS LEFT @ SOME GREAT PRICES.

 

 

Going Up.