Mizfit "Ouroboros" - 69 Camaro

[Mizfit MotorSports]

Project: Pro-Touring 1969 Camaro
X-44 Code
One owner
Sand blasted

2 inch Cowl
Smoothed Side Markers
Smoothed Fire Wall
New quarters
New trunk pan
New front fenders
New inner fender wells
Floor pans
New valance
New header Panel
Damn near all new sheet metal
New everything

Suspension:
Custom 4 link rear
Custom aftermarket front clip
Custom subframes
C4 front suspension
Mini Tubed
8 point Cage
New Dash
QA1 coilovers and springs
Vette front sway bar
LS1 rack
LS1 master

Brakes:
Baer Front 13 inch 2 pc cross drilled/slotted front with Baer 2 pistion front calipers
Baer Rear 12 inch 2 pc cross drilled/slotted rear rotors with LS1 rear calipers

Engine/Drivetrain:
427 CID "LS7 Block"
Kenne Bell Supercharger
Goal: 750-800 rwhp 6lbs boost
Eagle crank
Callies Rods
Federal bearings
Patriot Heads
ported Ls6 pump
rollmaster timing chain
Electric Water-Pump
Hooker Headers
Spec Stage 3 plus with Steel Flywheel
Custom Wiring
LS1 computer
ceramic coated 3inch Duals
Moser 9 inch 3:50 Gear Tru Trac
Upgraded Yoke
Custom Driveshaft
Custom Stainless Tank
Sheetmetal valve covers


Interior:
Custom Dash
Autometer Gauges
Corbeau Front seats recovered in leather and Hounds-tooth
Custom Dash Pad
New black carpet
New headliner
New door panels

Wheels/Tires:
Iforged Classics Stain Black Centers
18X9 fronts with 275 tire
18X10 rear with 305 tire

Most of these pics are old, I need to load the new ones on my computer. Everything as far as fabrication goes is finish ie: sheetmetal, 4 link, front clip etc...Car is being painted as we speak and should hopefully be together in one month. It will be for sale once it is finished. We are planning on taking the car to the Kruse auto auction.

[Mizfit MotorSports]

I did some photoshop work with another 69 "The Mule" I hope they don't mind. This picture is what I am guessing "Ouroboros" will look like except ours will have a satin black tail light panel and satin stripes on the side of the cowl. Also the last picture is the supercharger with our logo powdercoated on.





If we do this I think I will only do the "M" instead of the skull and wings and it will not be so bright. Still undecided..

[Mizfit MotorSports]

Feel free to check us out at www.fquick.com/Mizfit

[Mizfit MotorSports]

couple updated pics on : www.fquick.com/Mizfit

[Mizfit MotorSports]

some updates on the site above. Car came out of Paint and Body. Also stopped by and shot some pics of the seats which are almost done. Car is starting to take life.

[Mizfit MotorSports]

[Mizfit MotorSports]

[Mizfit MotorSports]

Here are some money shots of the wheels and paint! :unibrow:


nice little reflection of the poster on the wall.

[Mizfit MotorSports]

We pulled the rearend and 4 link today so I can take it to get powdercoated
tomorrow. Next will be the front sub, rack/pin and sway bar.

[Mizfit MotorSports]

I have some good news.. We finished building the motor and the Kenne Bell showed up which we then polished. This thing is killer
Click on pic for larger view: Sorry crappy phone pics

[Mizfit MotorSports]

NEW UPDATE....

1. Frame Powdercoated
2. A-Arm's cleaned up /semi-polished
3. Bumper Installed
4. Gas tank almost finished installing
5. Mocked up tail lights but not finished
6. Put Rear brakes on
7. Test fit front grill
8. Test fit Front Seats and door panels
9. Motor Installed

[Mizfit MotorSports]

CLICK PICS FOR LARGER VIEW::thumbsup:

[Mizfit MotorSports]

Next we are going to finish bumpers, lights, radiator, brake lines, fuel lines and pump. Then Glass will be put in and car will then be wired up, tuned and interior finished. Slow but steady. :woot: