yup, took advantage and got a shop vac, 24oz plumb bob, 5 mason hammers, 3 tape measures, 3pc pry bars, a bunch diggin and transfer shovels...shop vac for me, everything else for my business
I've joined that damn club three times. AND I HAVE YET TO GET MY CARD. Takes a few weeks to get your card he says. MY EYE IT DOES. I've been waiting for years and I'm done waiting. Anyway I'm about tooled out. The only tools I buy now are the specialty tools that craftsman dosn't have. I get the ones I need now from that rip off artist in the Snap-on Van. I limit those because I get an ear full when I get home. WIFE.
__________________ I never heard a man on his death bed say I wish I saved more money.
Thanks, just joined the club. The bearings on one of my Craftsman ratchets just went out after many years of faithful service, Sears replaced it in two minutes, no questions asked! I have yet to find a better tool/unconditional warranty around.
__________________ 2003 Tahoe Z71 5.3 Flex: Radix, CTS-V h/e, KB BAP, 40k cooler, Volant, 22" Magnaflow, Wheatley tune, Vette servos, Hotchkis sways, Bilsteins, 3.73s, hidden JL 10", PPI amp, Alpine 9853 face, Optima red top, Valentine 1
Waiting to be installed: HD2 shift kit, RAAMaudio sound deadening, PPI components
SOLD 95 Bronco XLT Sport 5.8 w/ 6" Superlift, 35s, JBAs, Magnaflow dual, MSD 6A, Jet chip, K&N CAI, 4.56s, locker, Warn hubs, Ranch Hand, Boston Acoustics, JL subs
Are the craftsman tool days going on right now? I got an e mail from sears. Just a little confused
Tool Days going on right now through Saturday, 3/12/05. I just picked up a 20' fiberglass extension ladder and 12 gallons of Weatherbeater Ultra housepaint (summer project) over the weekend. Saved $20 on the ladder and almost $100 on the paint
BTW, I joined the Club back on September 28 of 2004 and still don't have my card. I've called twice and still nothing. So far, I've just been using my card number or my phone number at the stores with no problems. I think I'll call again and see what they tell me this time...
MTI Clear Lid,Pacesetter LT's with ORY,LS6 intake,Janzter TB,
Strano springs,UMI suspension,TTII's 17x9.5/17x.11,WS9 hood Problems with your headlight?... READ MY STICKY!!
I went to sears on Saturday (May 14....craftsman days) and bought a 10mm wrench I had lost. Anyways, they didn't give me my 10% off. Apparently now you only get 10% off stuff listed in the monthly catalog, not everything. Kinda ticks me off.
I went to sears on Saturday (May 14....craftsman days) and bought a 10mm wrench I had lost. Anyways, they didn't give me my 10% off. Apparently now you only get 10% off stuff listed in the monthly catalog, not everything. Kinda ticks me off.
same here, pissed me off as well......makes me think 2x now before I buy a Craftsman over Dewalt or something else
just joined, i could barley understand the girl taking my information, had to go over it about 3 times. said it would be 6 to 8 weeks till i get the card. but it should be worth it. thanks tony..
I have a few friends that work for them. As mentioned the savings are only what is in the mailed flyer now. Since the merger/purchase of K-mart, Sears has been doing some goofy things.
The 10% off anything is gone, however, I was told if enough 'members' wrote and complained they may do it once a year/2x/quarterly or some such. They don't think it'll come back monthly again. Shame really.
So write in and bitch, 4 times a year is better than no times a year.
I have a few friends that work for them. As mentioned the savings are only what is in the mailed flyer now. Since the merger/purchase of K-mart, Sears has been doing some goofy things.
I noticed this last weekend that one of my local Sears stores that used to stock a lot of air tool accessories has dramatically cut down their stock. They barely had any open stock impact sockets at all now. Wonder if this is a sign of things to come...