.........
My build (truck/C6 manifold setup)
Thread Starter
10 Second Club
iTrader: (19)
Joined: Feb 2004
Posts: 2,542
Likes: 2
From: Alexandria La.
Thanks, I'm afraid the drain line wont drain right. I have the pan tapped on the front passengers side,the A/C compressor is right above it, the passengers side crossover is blocking it from the side and the front dosent look like it will work either. I knew it wouldnt be easy though.
Thread Starter
10 Second Club
iTrader: (19)
Joined: Feb 2004
Posts: 2,542
Likes: 2
From: Alexandria La.
Got a little more done yesterday.
Finished the drivers side of the crossover.
Tried to get as much clearance as I could for the 4" down pipe I plan to run so I had to make all these crazy bends.
Making a 45* fish mouth for the waste gate was fun.
For some reason I thought with this turbo I'd have more room, it fits OK but took up more room than I thought it should.
Finished the drivers side of the crossover.
Tried to get as much clearance as I could for the 4" down pipe I plan to run so I had to make all these crazy bends.
Making a 45* fish mouth for the waste gate was fun.
For some reason I thought with this turbo I'd have more room, it fits OK but took up more room than I thought it should.
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Thread Starter
10 Second Club
iTrader: (19)
Joined: Feb 2004
Posts: 2,542
Likes: 2
From: Alexandria La.
Thanks.
I guess it could be worse, I have a 00 TTI twin turbo C5 here that I changed an AC line on and there is NO room at all, huge PITA!
I guess it could be worse, I have a 00 TTI twin turbo C5 here that I changed an AC line on and there is NO room at all, huge PITA!
Thread Starter
10 Second Club
iTrader: (19)
Joined: Feb 2004
Posts: 2,542
Likes: 2
From: Alexandria La.
I have a BMR turbo K-member, it will fit going over the rack & under the steering shaft. It definitly makes things much easier.
Thanks.
Thanks.
hmmm do you have pics of the k member installed. i would like to see how much room. you will lose ground clearance going on teh driver side though. i did mine down the pass side but you are keeping AC. i made the 4 inch fit through there. i used a spohm k member with solid motor mounts. i used an older bmr one and gained no clearance over a stock k member.
keep up the good work i like some of the ideas you have. very well thought out
keep up the good work i like some of the ideas you have. very well thought out
Thread Starter
10 Second Club
iTrader: (19)
Joined: Feb 2004
Posts: 2,542
Likes: 2
From: Alexandria La.
hmmm do you have pics of the k member installed. i would like to see how much room. you will lose ground clearance going on teh driver side though. i did mine down the pass side but you are keeping AC. i made the 4 inch fit through there. i used a spohm k member with solid motor mounts. i used an older bmr one and gained no clearance over a stock k member.
keep up the good work i like some of the ideas you have. very well thought out
keep up the good work i like some of the ideas you have. very well thought out
From the back
From the front
Thread Starter
10 Second Club
iTrader: (19)
Joined: Feb 2004
Posts: 2,542
Likes: 2
From: Alexandria La.
Sure I'll get a pic up tonight, I had plenty of room with the K-member. I dont mind posting pics up, I learned a lot by looking at others pics and started a little collection of pics of Turbos/hotsides,intercoolers/cold sides, down pipes, & oiling. Hope my pics can help others like others pics helped me.
