Does it matter which way the head gaskets go on????
Does it matter which way the head gaskets go on???? Does it matter what direction the head gaskets go on on a ls1? My stang has a FRONT that has to face the front for cooling jacket purposes...Is the ls1 the same thing? I totally forgot about it when I put on the head gasket, does it matter?
If so is there a way I can tell which way it's on without pulling the head?
Thanks
If so is there a way I can tell which way it's on without pulling the head?
Thanks
Jon
Gasket should have front on it and obviously that is the top.
Heads do not have a front and back, they can go on either side. Your coolant tempsensor is on your D/S head though.
Heads do not have a front and back, they can go on either side. Your coolant tempsensor is on your D/S head though.
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo Thank you, the coolant ducks are not the same for the 5.3 heads. The driver side heads have a ground the passenger side do not. Your driver side heads have the bolt pattern for the power steering pump the passenger side do not.
But for those of you who do not think so please go ahead and place then on which ever side you want.
Where does the OP say he has a 5.3? He says he has an LS1.
THE LS1/LS6 HEADS CAN BE INSTALLED ON EITHER SIDE. THEY ARE NOT MARKED FRONT AND/OR BACK.
This is how BS gets perpetuated on the internet. I have a pair of LS1 casting # 241 heads on the shelf and I also have a pair of LS6 casting # 243 heads on the shelf.
They are the same with the same bolt pattern on each end and the passages cast the same on each head.
I looked real hard but couldn't find any ducks in any of them.
THE LS1/LS6 HEADS CAN BE INSTALLED ON EITHER SIDE. THEY ARE NOT MARKED FRONT AND/OR BACK.
This is how BS gets perpetuated on the internet. I have a pair of LS1 casting # 241 heads on the shelf and I also have a pair of LS6 casting # 243 heads on the shelf.
They are the same with the same bolt pattern on each end and the passages cast the same on each head.
I looked real hard but couldn't find any ducks in any of them.
Found a picture from when I was putting things together
I'm not arguing the heads matter which side they go on, only that the gaskets have a "FRONT", which was the original question in this thread.
Last edited by Hilton; Aug 3, 2009 at 12:00 PM. Reason: added a picture
I never said he had a 5.3 only that it does matter on a 5.3 which is front and back as far as the gasket goes. The LS1 gasket should also be the same as noted in the above pic. As far as the heads go they should be able to go on either side.
And I said that the head gaskets are marked 'front' in post #6. I guess you missed that. 