Progress pics of my MPT76 Front Mount 01 SS.
where did u get the 4in for your dp?
Thread Starter
TECH Fanatic
iTrader: (16)
Joined: Dec 2005
Posts: 1,299
Likes: 1
From: Alvarado, Texas
Will grind the welds down tonight, coat and wrap it. 
Not too bad welding, nothing a grinder won't handle, but it did take about 2 hours to cut all the bends, funning thing is I cut all the bends with a reciprocating saw with no tape measure!!
4" Dump next to tranny, will be attaching a 4" pipe and run it to the axle with a bullet muffler and dump.
Not too bad welding, nothing a grinder won't handle, but it did take about 2 hours to cut all the bends, funning thing is I cut all the bends with a reciprocating saw with no tape measure!!
4" Dump next to tranny, will be attaching a 4" pipe and run it to the axle with a bullet muffler and dump.
Last edited by Vcious04; Nov 4, 2011 at 10:17 PM.
Thread Starter
TECH Fanatic
iTrader: (16)
Joined: Dec 2005
Posts: 1,299
Likes: 1
From: Alvarado, Texas
Finished painting all the cold pipes, wrapping hot pipes and almost done with down pipe (waiting on v-band clamp). Re-routed the power steering lines, grinded all the welds, finished radiator mount, installed TR6's, tapped and installed boost guage, connectors injector harness.
Thread Starter
TECH Fanatic
iTrader: (16)
Joined: Dec 2005
Posts: 1,299
Likes: 1
From: Alvarado, Texas
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo Thread Starter
TECH Fanatic
iTrader: (16)
Joined: Dec 2005
Posts: 1,299
Likes: 1
From: Alvarado, Texas
Registered User
Joined: Aug 2009
Posts: 5
Likes: 0
From: Wyoming Gillette
Lol!!! just working at the coal mines. Installed my 3" ETS Downpipe VTA, Home made Intake Got my stuff for EcuFlash and been road tuning this last weekend and doing lot of logging when I get a chance. LC-1 Wideband should be here tomorrow so can do my AFR with out blowing my crap up so right now running 23Psi/19psi redline. But Should be running pig rich right now like 10-9 AFR's so got to lean it out hope this week to better AFR reading right. Nope no snow yet. Will be here by end of the month or shorter. Here is a video of my car by the way. Should hear it in person man f*&^%^$ LOUD!
http://www.youtube.com/watch?v=EduWZo2X7Go
http://www.youtube.com/watch?v=EduWZo2X7Go
Looks good. Only thing i would suggest is throw a vband on the merge. Makes putting it on and off a hell of alot easier. I seem to like to take my car apart a lot though.
Good luck, Chris
Good luck, Chris
lol haha i like the plate
and shutup chris, you have a race car with your pit crew.... you better get used to your car getting torn apart and built again all the time!
million dollar race car vs my scrap crap
lol
and shutup chris, you have a race car with your pit crew.... you better get used to your car getting torn apart and built again all the time!
million dollar race car vs my scrap crap
lol
Thread Starter
TECH Fanatic
iTrader: (16)
Joined: Dec 2005
Posts: 1,299
Likes: 1
From: Alvarado, Texas
Thanks everyone for the interest and support.
I have been pretty sick with the flu the last fews days and haven't touched it.
I am done mechanically but am having tuning issues and plan on having a full dyno tune completed this saturday. I will keep ya'll posted!! Thanks!
New pics!!
I have been pretty sick with the flu the last fews days and haven't touched it.
I am done mechanically but am having tuning issues and plan on having a full dyno tune completed this saturday. I will keep ya'll posted!! Thanks!
New pics!!
not worried about overheating with the stock radiator stood straight up, I thought it wasn't made to do that and water would not stay in it long enough to cool? You will have to keep us posted on how it does.