Great Nitrous tuner needed...
Thats cheap !
We have spent 20-30 thousand dollars learning how not to blow **** up and someone is gonna get all that info for $300.
Hell we probably give up to much info on here.
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Wayne, the knowledge is priceless. ****, I should have flown you guys out to party...er .....tune my junk up here.
I'm looking for a great tuner in the south who will actually take the time to pull plugs, change jets dozens of times, flow and adjust standalone pressures, experiment with plugs (need a plug that will daily drive and be able to do up to a 300 shot), and experiment with na timing before moving to the nitrous tune. Some one who will make every effort for a safe tune no matter how long it takes...I also need a switch to pull timing for second stage through efi live...
Going to be a forged 346 with 2 kits on a dual window switch and stand-alone
There is a wideband in car
Car is going to be a roll race vehicle
Has to be able to do a single shot on close to stock timing with c16 in the stand-alone
also need a little drivability tuning....
Car needs to idle well and drive close to stock on a plug that will atleast support a 250 shot... Cam in the 230's at .050ths
Who do you recommend?
Going to be a forged 346 with 2 kits on a dual window switch and stand-alone
There is a wideband in car
Car is going to be a roll race vehicle
Has to be able to do a single shot on close to stock timing with c16 in the stand-alone
also need a little drivability tuning....
Car needs to idle well and drive close to stock on a plug that will atleast support a 250 shot... Cam in the 230's at .050ths
Who do you recommend?
what about Monte Smith?
or talk to Steve @ Induction Solutions in Florida...both of these guys know what the hell is up with nitrous and tune some of the fastest cars in the country period.
good luck in your endeavors, its going to be real hard to get a plug to live on the street that will handle a 300 shot, also if your doing 2 stages once your tuned on two stages...its not really advisable to go back to the single stage.
if not them RPM.
Chad
or talk to Steve @ Induction Solutions in Florida...both of these guys know what the hell is up with nitrous and tune some of the fastest cars in the country period.
good luck in your endeavors, its going to be real hard to get a plug to live on the street that will handle a 300 shot, also if your doing 2 stages once your tuned on two stages...its not really advisable to go back to the single stage.
if not them RPM.
Chad
Thread Starter
TECH Resident
iTrader: (13)
Joined: Jan 2004
Posts: 992
Likes: 0
From: South Carolina
Thread Starter
TECH Resident
iTrader: (13)
Joined: Jan 2004
Posts: 992
Likes: 0
From: South Carolina
Don't feel bad, I got my *** handed to me by a silver evo in columbia when i had a stock ta with a 200 shot, he left me like I was standing still...all I could think was WTF and never even found out who he was...stuff happens...
FormerVendor
Joined: Oct 2007
Posts: 34
Likes: 0
Seriously though, take a look at our affiliate, www.SECdyno.com for details. When you call ask for Jim. He's been in this industry since 1981, the best tuner I've ever dealt with and very meticulous.
btw, slammin86, thats a great looking GTO!
