Code-PO327 Sensor 1 low input(Knock sensor)
Thread Starter
11 Second Club
iTrader: (15)
Joined: Aug 2007
Posts: 603
Likes: 3
From: Royal Oak, Mi
Code-PO327 Sensor 1 low input(Knock sensor) My question is is it the knock sensor setting this code or o2 sensor? The passenger side has a new o2 sensor in it. My car has thrown occasional knock sensor codes, but now it will not go away and performance at the track is hurting, so I believe it's cutting timing. The description of the code is throwing me off(low input), does that mean that sensor is bad, or that a bad o2 could be throwing this code(driver side o2 is older than passenger).
Thread Starter
11 Second Club
iTrader: (15)
Joined: Aug 2007
Posts: 603
Likes: 3
From: Royal Oak, Mi
Just checked the codes again...It now threw another o2(bank 2, sensor 1) code....could this be because of the bad knock sensor? I plan on pulling the intake a little later and putting a new knock sensor in to see if that helps.
Teching In
Joined: Oct 2009
Posts: 3
Likes: 0
Knock snesor code Here is what I have learned since my initial posting. The Knock sensor in the LS1 is a single wire unit and diagnostics only can determine that it is reading a knock or the sensor has failed. The GM mechanic assumes if there is no additional codes the sensor must be bad. I had very bad fuel in the 99TA I bought. It hadn't been driven in 5 years and know one told me that. As a result the car knocked and had no other code so the "assume" it is the sensor. I drained the tank added new fuel and cleaned the top end and it runs like a top. The mechanics I talked to said the knock sensors rarely fail, and usually the knock sensor code is secondary to another problem. You can even have false knock. Such as a header hitting the frame and the sensor reads this as knock. Look long and hard before you pull the intake manifold to replace the knock sensor it may not be the problem.
Trending Topics
12 Second Club
Joined: Feb 2005
Posts: 147
Likes: 0
From: baytown, tx
its funny that you say that because i just finished replacing my knock sensors. Sensor 2 was rusted, i guess the grommet didn't keep the water out at all. But to the OP i suggest you replace them both, it's an annoying fix but it's not too hard.
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Launching!
Joined: Feb 2004
Posts: 260
Likes: 0
Easy answer is to cover them with protective grease and attempt to waterproof the rubber grommet on the valley plate also.
P0327 usually happens when the KS or the wiring has a fault, not from bad fuel.
Teching In
Joined: Oct 2009
Posts: 3
Likes: 0
Misunderstood The idea wasn't that you had fuel! It was that other conditions can cause you to get a bad Knock snesor code. Including mechanical contact knocks. The factory diagnosis process follows that if no other code is shown the KS is bad. The advice that knock sensors rarely fail came from a California builder and friend. Maybe they have less "rust" problems then we do in cold states. Either way I am glad I took a look at all other factors before I pulled the intake manifold. If not your concern go for it!
