Homebuilt Frontmount TC76 Truck Manifold Build
Thread Starter
Joined: Nov 2001
Posts: 3,406
Likes: 2
From: Tallahassee, Fl
i have the trap door from when i did my fuel pump BUT i dont have a battery right now and the hatch is shut which is a small but solvable problem. also i made a feeble attempt to push the connectors over the tank with it strapped in and couldnt get them up there, ill try again a little harder though
Thread Starter
Joined: Nov 2001
Posts: 3,406
Likes: 2
From: Tallahassee, Fl
made the slide tensioner outta some flat stock
LMFAO! atleast your key works for your hatch and doors! mine doesnt!!! Battery died and couldn't get into car!!!! had to jack it up and put jupers on starter and frame! lmao, sucked!
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
I did a Racetronix and harness just a couple weeks ago. Just unbolt the tank straps and let the tank settle. You should have enough room to slide the end of the harness up and over the EVAP cannister. My long arms and big hands actually HELPED this time 
.
. Thread Starter
Joined: Nov 2001
Posts: 3,406
Likes: 2
From: Tallahassee, Fl
figured post an update
pump wiring is finished, got the rear back,out with the 4.30's in with 3.70's, new rod ends in the lca's, and 275/50/17 M&H drag radials. i had issues with a prior set and their customer service was awesome and they gave me a set of them from a new wider mold. they are about as wide as my 275/40/17 M/T drag radials were
heres some more with pics
finished the downpipe
also got the gauges installed.
fuel pressure gauge (WAY more of a pain in than the *** than i thought it would be)
gauges in the vents, boost, water temp, and LC1 wideband. i have the fernco piece to center the gauge in the 2 5/8" hole that i will put in tomorrow.
Engine bay pics
figuring out hptuners as i go. got a base tune loaded on weds and after four months she fired right up. tune was way off so i started over tonight and got a new tune loaded and things went much better. idles great, afr at idle is between 12-14. gotta get used to the sound coming from a choppy heads and cam setup but it sounds great
coming along....
pump wiring is finished, got the rear back,out with the 4.30's in with 3.70's, new rod ends in the lca's, and 275/50/17 M&H drag radials. i had issues with a prior set and their customer service was awesome and they gave me a set of them from a new wider mold. they are about as wide as my 275/40/17 M/T drag radials were
heres some more with pics
finished the downpipe
also got the gauges installed.
fuel pressure gauge (WAY more of a pain in than the *** than i thought it would be)
gauges in the vents, boost, water temp, and LC1 wideband. i have the fernco piece to center the gauge in the 2 5/8" hole that i will put in tomorrow.
Engine bay pics
figuring out hptuners as i go. got a base tune loaded on weds and after four months she fired right up. tune was way off so i started over tonight and got a new tune loaded and things went much better. idles great, afr at idle is between 12-14. gotta get used to the sound coming from a choppy heads and cam setup but it sounds great
coming along....
Last edited by Tally TransAm; Oct 16, 2009 at 08:54 PM.
Thread Starter
Joined: Nov 2001
Posts: 3,406
Likes: 2
From: Tallahassee, Fl
got a local hydraulic shop to make new power steering lines with my stock ends for like 35 bucks.
alt bracket needs a little fine tuning but i think it will work. on first start up the belt started to come over the top of the power steering pulley, move it back a little and it is staying put now but might need to move it back a little more
alt bracket needs a little fine tuning but i think it will work. on first start up the belt started to come over the top of the power steering pulley, move it back a little and it is staying put now but might need to move it back a little more
Thread Starter
Joined: Nov 2001
Posts: 3,406
Likes: 2
From: Tallahassee, Fl
got a local hydraulic shop to make new power steering lines with my stock ends for like 35 bucks.
alt bracket needs a little fine tuning but i think it will work. on first start up the belt started to come over the top of the power steering pulley, move it back a little and it is staying put now but might need to move it back a little more
alt bracket needs a little fine tuning but i think it will work. on first start up the belt started to come over the top of the power steering pulley, move it back a little and it is staying put now but might need to move it back a little more
Don't mean to hi-jack or anything, but I used his idea, all the pics and info are in my build thread and I actually have drove my car about 50 miles and it seems to be working good! Link in sig.
