I'm putting this up for sale to gauge any interest. I don't need to sell it but it it sells it will help me pay off some debt that I would much rather have paid off and linger over my head.

The car is a LS3 swapped 2001 Pontiac Trans Am WS6 Red M6 with all bolt-ons and a cam. The interior is black ebony leather with the seats in good condition. It has about 118K miles on the car. The car has been a southern car up until I bought it, but has never seen snow. The body is pretty much rust free if any at all. The engine and clutch has just under 10,000 miles on it.

The engine has been properly broken in and has run great with no issues. During the break-in process I used Rottela T and a K&N filter. I have always used K&N filters on this engine. After the break-in period I have used Castrol Syntec 0W-30 or 5W-30. I have seen no metal shavings come out of the pan when doing oil changes. Oil changes were done ever 2500-3000 miles.

When I got it dyno tuned it put down 435RWHP, but the tuner said his dyno reads low. For example C6 Z06's dyno 435RWHP on his dyno but dyno 455RWHP everywhere else. Though with the cutout now installed it seems about 15 RWHP/RWTQ is added. TJ at Baker Engineering tuned it and it runs and drives very smooth. I drive it everyday and I can cruise at 40mph in sixth at 900 rpms even with the cam. This car could EASILY be in the 480-490RWHP range with a Stage 2 Ported Intake.

If there are any other questions please don't hesitate to post or PM me. Anyways here is a list of modifications, the dyno video. I will add some pictures at the end.

LS3 Trans Am Dyno Here is a video open headers before the tune

Link to Pictures - Click Here

Engine Specs Rebuilt by me with all specs in check.
2008 L92 6.2L 376c.i. Short Block - Rebuilt (Hone Cylinder Walls, Polished/Mic’d Crank, Clevite 77 Cam Bearings, Clevite 77 Main Bearings, Clevite 77 Rod Bearings, New GM Rings, Stock L92 rotating assembly)
LS3 Front Cover with Cam sensor

Valvetrain/Heads
Stock L92 cast heads, 10.5:1 Compression
Stock Rocker Arms
LS3 Intake and Exhaust Valves
TEA Dual Gold Spring Kit, .650 lift
LS7 Lifters
Comp Cams Chromeoly Hardened 7.4 Pushrods
Vengeance Racing LS3 Stage 3 Camshaft
LS3 Timing Chain Dampener 3 Bolt 4X Cam Gear
LS3 Timing Chain
LS6 Oil Pump
Stock GM MLS Head Gaskets

Transmission Works great with no grinding
Stock T-56
Short Stick
LS7 Clutch Kit

Rearend/Driveshaft – The rear feels great with no whining or anything.
No TCS only ABS
Stock 3.42 Gears (Will throw in a set of brand new GM 4.10's)
Stock Aluminum Driveshaft

Electrical
Lingenfelter Performance TRG-001: 58x to 24x Converter Box
85mm Delphi MAF with Adapter Harness
LS2 Knock Sensor Adapter Harness
MSD 8.5mm Super Conductor Spark Plug Wires
TR-5IX Iridium Spark Plugs
Yellow Top Optima Battery
L76 MAP Sensor
Delco Injector Adapters
Autometer C2 Fuel Pressure and Narrow Band Gauges in a dual pillar pod.

Induction
WS6 Ramair – Hood and lower intake box
L76 Intake Manifold
FAST 90mm Cable Driven Throttle Body
85mm TSP Lid K&N Drop in Air filter

Fuel/Cooling
L76 Fuel Rails 40lb LS7 Injectors - Adapters for LS1
Twin Walbro 255lph In-Tank Fuel Pumps

Exhaust
Pacesetter Headers
ORY - 3” -4” Flowmaster Merge
4” cutout with DMH Electric Cutout
4”-3” reducer back to a SLP Dual/Dual Exhaust

Appearance
WS6 Package
T-Tops with matching interior shades - I also have an extra set of T-Tops to go to the buyer!
17x9.5 Chrome C5 Z06 Wheels with chrome lugs
275/40R17 Fuzion ZRi's with 15% tread left on the front
285/40/17ZR Nitto 555's 80% tread
Windows Tinted 20%
Red Painted Calipers
The Fog lights have HID's 8000K in color

Suspension/Braking
WS6 Sway Bars
Eibach Sportline Springs
KYB Rear shocks
Stock Front Struts
UMI Adjustable Torque Arm
UMI Rear Tubular Control Arms
Strut Tower Bar
Polyurethane Motor Mounts
Polyurethane Trans Mount
Polyurethane Torque Arm Mount
Polyurethane Front Sway Bar Links
Powerstop Slotted/Coated rotors all around
Z16 Ceramic Pads Front and Back

Interior
Black Ebony Leather
Pioneer CD/MP3 deck
6-Way Power Drive Seat Power
Lumbar for Passenger Seat
Two Keyless Entry Key Fobs and Keys
Window motors work great

The not so good: I had a child of a friend think it would be fun to take his toy car to my car and well it left some pretty deep scratches. I left it with the intent of getting the whole car repainted this winter. The clear has really peeled back on the hood but most of the other scratches are pretty shallow. There is some clear peeling on the drivers door. There are also rock chips on the front bumper and headlight covers and some scrapes on the bumper and rockers from bottoming out. The sail Panel has some bubbling. The arm rest button is missing and there is a crack in the driver door panel. The driver seat is getting worn on the bolster but hasn't worn all the way through. There is a wear spot through the carpet by the gas pedal.

Again this car is a great car whether it be someones daily driver or weekend car. With the cutout closed the car is barely louder than stock and virtually no rasp due to the Flowmaster merge. With the cutout open it sounds amazing and definitely turns heads with lots of approval. I have taken this car on two 2000 mile trips and wouldn't hesitate to do it again. I averaged between 20-22 mpg on the trips. The heat blows hot and the A/C is ice cold. The car definitely turns heads and I hate to think about selling it but like I said before I would really like to get out of debt. The car runs great with no mechanical hiccups, just needs a few cosmetic fixes. Also the car has a clean title with no accidents. I would be looking for around $12K firm as it sits. The car will be going to the paint shop in the next couple weeks. When that is done I will be asking $14K firm. Again I am gauging interest so please feel free to ask questions. Thanks for looking!

 

Bumb for a ba motor!! You must be a
mechanic? Where'd u get the ls3?

 

Thanks it definitely is a bad *** engine! I'm not a mechanic by trade just something that me and my whole family has been into for a long time. I got the engine here in Michigan from a guy that was going to use it for a project and never got around to it.

And for anyone interested the pictures will be up tonight! If I could get a few potential buyers by the end of the week that would be great!

 

Thats one bad **** !!

 

Thanks!

A link to pictures has been added just below the videos.

 

PM's replied

 

Oh I also forgot to add the I have an extra set of T-Tops to go with the car.

 

Beautiful T/A man. Lately I have been thinking about getting out of my Lightning and in an LS1. Car looks great GLWS

 

Bump for the day!

 

Lots of lookers! Shoot me some offers if there's some interest!!!

 

Bump for the day!

 

Let see if I can't get some more interest, $13.5K to anyone that wants it painted.

Also I think I'll throw it up on eBay sometime this week.

 

man i wish i could have another one..

 

Well lets help that wish come true! haha!

 

Bump for a BadA** T/A

 

Thanks for the bump! Your T/A is CLEAN!!!

I'll be putting it up on eBay tomorrow. I've got another car that I am interested in, but I need to sell this one first.

 

Car is now on eBay, here is the link:

http://cgi.ebay.com/ebaymotors/ws/eB...STRK:MESELX:IT

 

Back up to the top for the day!

 

Hmm I wonder how this thing would do with a FAST 102mm intake/throttle body..

 

Probably only slightly better than a stock manifold with stage 2 porting from Jeremey F...