Bolt in Fab 9 Housing
Bolt in Fab 9 Housing....GP.. Hi everyone Burkhart Chassis is new to LS1Tech but the products are not. We are going to offer the Famous Fab 9 Housing at a price I don't think has ever been done. $999.00
You can see these and other products we offer at our new website below.
You can see these and other products we offer at our new website below.
Last edited by Dave@BurkhartChassis; Dec 18, 2006 at 10:09 PM.
Originally Posted by skipperbisket
hmmm, offering any kind of deal on trading my brand new moser 9" housing and 35spl. axles for my cash and one of the fab9 housings and new axles?
Trending Topics
Originally Posted by ls1king000
Does the Fab 9 work with a stock/aftermarket (spohn) sway bar?
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
Originally Posted by skipperbisket
i need to go to a narrowed housing, thats why i wanna ditch mine. thanks, i'm going to try to sell mine to get one that you guys are offering.
How hard would it be to fit a 2" narrowed Fabbed 9" in my car, thats lowered somewhere around two inches?
True bolt in housing? Can the spring perches be left off? How hard would it be to run my current LG swaybar?
Thanks in advance
Rob
True bolt in housing? Can the spring perches be left off? How hard would it be to run my current LG swaybar?
Thanks in advance
Rob
Originally Posted by BAD *** TA WS6
How hard would it be to fit a 2" narrowed Fabbed 9" in my car, thats lowered somewhere around two inches?
True bolt in housing? Can the spring perches be left off? How hard would it be to run my current LG swaybar?
Thanks in advance
Rob
True bolt in housing? Can the spring perches be left off? How hard would it be to run my current LG swaybar?
Thanks in advance
Rob
Last edited by Dave@BurkhartChassis; Dec 10, 2006 at 11:29 AM.
Originally Posted by Dave@BurkhartChassis
Sorry fot thr the delay I still dont have internet service do to the storm.It should not be any problems fitting it in your car.. We can leave off the sripng perches if you like. The only this you might have a problem with is your wheels..Thanks
How much does your fabbed assembly weigh? (including gear set/axles etc.) I'd just be looking to do an Eaton posi setup most likely.
As for the rear wheels, I'll be having 2 new sets made. With a much larger dish...
Originally Posted by BAD *** TA WS6
A competitor told me differently. It took 3 weeks to get an answer out of them... I am low, and the gas tank is close....
How much does your fabbed assembly weigh? (including gear set/axles etc.) I'd just be looking to do an Eaton posi setup most likely.
As for the rear wheels, I'll be having 2 new sets made. With a much larger dish...
How much does your fabbed assembly weigh? (including gear set/axles etc.) I'd just be looking to do an Eaton posi setup most likely.
As for the rear wheels, I'll be having 2 new sets made. With a much larger dish...
one more question, is the $999 for Any width rear, or stock width? if i were to buy one narrowed could i send my wolfe swaybar setup to you and have that installed too before you ship the housing?
Originally Posted by skipperbisket
one more question, is the $999 for Any width rear, or stock width? if i were to buy one narrowed could i send my wolfe swaybar setup to you and have that installed too before you ship the housing?
Originally Posted by ricknbird350
do you sell complete rear ends? i sold my 12 bolt and want a 9" posi with 3.90,no abs
Originally Posted by Dave@BurkhartChassis
I must be missing something if they told you it wont work. Care to elaborate to why it wont work? The housings loaded with strage parts are around 180lbs. We are assembling one with all moser stuff so I will have the weight on that soon..
I run coil overs all the way around, that's why I want to ditch the spring perches. I'd also be interested in having you guys mount up my swaybar before shipping it out.
I'll be running a big dog set of Mov-It brakes in the rear. I don't forsee any problems with how the brake caliper mounting brackets are positioned correct?
Pm me a ballpark price for the narrowed fabbed 9" with installed swaybar and say an Eaton posi 3.08 gear set. Doesn't have to be exact, just a rough estimate. I'll get back to you guys when I'm ready to order the new rear wheels, brakes and your rear.
Rob Borowski