Guys with over 800rwhp whats your fuel system
Thread Starter
TECH Regular
iTrader: (2)
Joined: May 2004
Posts: 406
Likes: 0
From: Kitchener, Ontario
Guys with over 800rwhp whats your fuel system Looking to put to geather a fuel system for the T/A ....for the 800+ rwhp mark...this is a boosted eng as well....
looking for a parts list....
thanks
looking for a parts list....
thanks
Give me a call, I can set you up with a complete system that is proven to feed your engine with a couple hundred extra HP to spare.
It will connnect to your double pumper kit to complete the package.
For more information, I can be reached at (724)322-8505 7:00pm-11:00pm eastern time weekdays & 9:00am-11:00pm weekends.
It will connnect to your double pumper kit to complete the package.
For more information, I can be reached at (724)322-8505 7:00pm-11:00pm eastern time weekdays & 9:00am-11:00pm weekends.
I'm hoping dual intank pumps will do it for my turbo car. Is something like the MSD voltage booster necessary or is something like the Racetronix hot wire kit adequate?
Trending Topics
LS1 Tech Stories
The Best V8 Stories One Small Block at Time
Topdon ONE vs. Artidiag 800 BT2: Which is the Diagnostic Tablet For You?
Pouria Savadkouei
Gas Monkey Built a 6-Wheel Ferrari Testarossa With a Corvette LT4 Engine
Verdad Gallardo
7 Most Reliable High-Performance Engines GM Has Ever Built
Verdad Gallardo
Amazing '71 Camaro Restomod Is Modern Muscle Car Under the Skin
Verdad Gallardo
6 Common C5 Corvette Failures and What's Involved In Repairing Them
Pouria Savadkouei
Retro Modern Bandit Pontiac Trans AM Comes With Burt Reynolds' Autograph
Verdad Gallardo
Top 10 Greatest Cadillac V Series Performance Models Ever, Ranked
Pouria Savadkouei
Top 10 Most Powerful Chevy Trucks Ever Made!
Hennessey's New Supercharged Silverado ZR2 Has 700 HP
Verdad Gallardo
My advice. If you are spending the money to make 800 rwhp do not slack on your fuel system. Spend the money on good stuff such as an Aeromotive A1000 pump and regulator, -10 feed line, -6 return, sumped tank, fuel cooler.....etc.
Originally Posted by daniel6718
what are yall doing about one of them failing? i keep hearing people mention that what if one fails but i dont hear and responses
Originally Posted by RealQuick
What happens if you run a A1000 and it dies under WOT? Same thing. Your fucked no matter what if a pump dies (whether you have 2 or 1).
Originally Posted by Speed Density
I run a Magnafuel 4302 pump, A1000 regulator. -8 Feed and -6 return.
All the goodies too, pre/post filters, cutoff, cooler etc...
Tony.
All the goodies too, pre/post filters, cutoff, cooler etc...
Tony.
You cant see my setup at all, it looks baller.
Ive even got the Twist Loc blue -12 hose to the pump, so it stands out. But you cannot see it from any angle.
Pump Mounted.
Pump and Filter
Tony.
Ive even got the Twist Loc blue -12 hose to the pump, so it stands out. But you cannot see it from any angle.
Pump Mounted.
Pump and Filter
Tony.
To clarify a few items...
To address Walbro failures, I have been building double pumpers for Racetronix for over 3 years without a pump failure.
As for power capability, I have replaced A1000 pumps, that could not feed the motor, with my Double pumper kits. These have supported well over 900rwhp without any type of volt boosters. The A1000 is usually good for about 800 flywheel hp when it comes to forced induction EFI applications at elevated fuel pressures.
Sumped tanks definitely have their place, but for most applications that are street driven, the dual intank setup is queter, does not require a pump controller on the street & will likely feed most cars well into the 8sec range.
Since Jeremy already has the pump system, there is no reason to change it. Add lines, rails & regulator & it should meet all of his needs.
To address Walbro failures, I have been building double pumpers for Racetronix for over 3 years without a pump failure.
As for power capability, I have replaced A1000 pumps, that could not feed the motor, with my Double pumper kits. These have supported well over 900rwhp without any type of volt boosters. The A1000 is usually good for about 800 flywheel hp when it comes to forced induction EFI applications at elevated fuel pressures.
Sumped tanks definitely have their place, but for most applications that are street driven, the dual intank setup is queter, does not require a pump controller on the street & will likely feed most cars well into the 8sec range.
Since Jeremy already has the pump system, there is no reason to change it. Add lines, rails & regulator & it should meet all of his needs.
Staging Lane
Joined: Sep 2006
Posts: 50
Likes: 0
From: Wisconsin
I have a Ricks stainless tank in my second gen running two gs340 walbro pumps ,the second pump comes on only when fuel pressure drops, done with hobes pressure switch, running two 6an lines to a y block than a 8an line with 6 an return, my ls-7 has 711 flywheel hp works great
Originally Posted by Speed Density
You cant see my setup at all, it looks baller.
Ive even got the Twist Loc blue -12 hose to the pump, so it stands out. But you cannot see it from any angle.
Tony.
Ive even got the Twist Loc blue -12 hose to the pump, so it stands out. But you cannot see it from any angle.
Tony.
